Техническая Спецификация для Plastidip Liquid rubber coating spray Colour Neon green 61090017 400 ml 61090017
Модели
61090017
Page 4/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 28.02.2012
Revision: 28.02.2012
Version 2
Trade name: PLASTI DIP® FLÜSSIGGUMMI SPRAY
(Contd. of page 3)
34.0
6 Accidental release measures
Personal precautions, protective equipment and emergency procedures
Wear protective equipment. Keep unprotected persons away.
Keep away from ignition sources.
Ensure adequate ventilation.
Environmental precautions: Do not allow product to reach sewage system or any water course.
Methods and material for containment and cleaning up:
Absorb with liquid+binding material (sand, diatomite, acid binders, universal binders, sawdust).
Reference to other sections
See Section 7 for information on safe handling.
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.
Wear protective equipment. Keep unprotected persons away.
Keep away from ignition sources.
Ensure adequate ventilation.
Environmental precautions: Do not allow product to reach sewage system or any water course.
Methods and material for containment and cleaning up:
Absorb with liquid+binding material (sand, diatomite, acid binders, universal binders, sawdust).
Reference to other sections
See Section 7 for information on safe handling.
See Section 8 for information on personal protection equipment.
See Section 13 for disposal information.
7 Handling and storage
Handling:
Precautions for safe handling
Keep receptacles tightly sealed.
Use solvent+proof equipment.
Ensure good interior ventilation, especially at floor level. (Fumes are heavier than air).
Precautions for safe handling
Keep receptacles tightly sealed.
Use solvent+proof equipment.
Ensure good interior ventilation, especially at floor level. (Fumes are heavier than air).
Information about fire < and explosion protection:
Keep ignition sources away + Do not smoke.
Protect against electrostatic charges.
Protect from heat.
Keep ignition sources away + Do not smoke.
Protect against electrostatic charges.
Protect from heat.
Conditions for safe storage, including any incompatibilities
Storage:
Requirements to be met by storerooms and receptacles:
Store in a cool location.
Storerooms must be well ventilated.
Keep container tightly closed.
Storage:
Requirements to be met by storerooms and receptacles:
Store in a cool location.
Storerooms must be well ventilated.
Keep container tightly closed.
Information about storage in one common storage facility:
Storage in the near of other chemicals or products has to be verified.
Storage in the near of other chemicals or products has to be verified.
Further information about storage conditions: Protect from heat and direct sunlight.
Specific end use(s) No further relevant information available.
Specific end use(s) No further relevant information available.
8 Exposure controls/personal protection
Additional information about design of technical facilities: No further data; see item 7.
Control parameters
Ingredients with limit values that require monitoring at the workplace:
Ingredients with limit values that require monitoring at the workplace:
115<10<6 dimethyl ether
WEL (Great Britain)
WEL (Great Britain)
IOELV (EU)
Short+term value: 958 mg/m³, 500 ppm
Long+term value: 766 mg/m³, 400 ppm
Long+term value: 1920 mg/m³, 1000 ppm
Long+term value: 766 mg/m³, 400 ppm
Long+term value: 1920 mg/m³, 1000 ppm
1330<20<7 xylene
WEL (Great Britain)
WEL (Great Britain)
IOELV (EU)
Short+term value: 441 mg/m³, 100 ppm
Long+term value: 220 mg/m³, 50 ppm
Sk; BMGV
Short+term value: 442 mg/m³, 100 ppm
Long+term value: 221 mg/m³, 50 ppm
Skin
Long+term value: 220 mg/m³, 50 ppm
Sk; BMGV
Short+term value: 442 mg/m³, 100 ppm
Long+term value: 221 mg/m³, 50 ppm
Skin
141<78<6 ethyl acetate
WEL (Great Britain) Short+term value: 400 ppm
WEL (Great Britain) Short+term value: 400 ppm
Long+term value: 200 ppm
(Contd. on page 5)
GB