Техническая Спецификация для Plastidip Liquid rubber coating spray Colour Neon green 61090017 400 ml 61090017
Модели
61090017
Page 5/9
Safety data sheet
according to 1907/2006/EC, Article 31
Printing date 28.02.2012
Revision: 28.02.2012
Version 2
Trade name: PLASTI DIP® FLÜSSIGGUMMI SPRAY
(Contd. of page 4)
34.0
78<93<3 butanone
WEL (Great Britain)
WEL (Great Britain)
IOELV (EU)
Short+term value: 899 mg/m³, 300 ppm
Long+term value: 600 mg/m³, 200 ppm
Sk
Short+term value: 900 mg/m³, 300 ppm
Long+term value: 600 mg/m³, 200 ppm
Long+term value: 600 mg/m³, 200 ppm
Sk
Short+term value: 900 mg/m³, 300 ppm
Long+term value: 600 mg/m³, 200 ppm
142<82<5 heptane
WEL (Great Britain)
IOELV (EU)
WEL (Great Britain)
IOELV (EU)
Long+term value: 500 ppm
Long+term value: 2085 mg/m³, 500 ppm
Long+term value: 2085 mg/m³, 500 ppm
DNELs Not determined.
Additional information: The lists valid during the making were used as basis.
Exposure controls
Personal protective equipment:
General protective and hygienic measures:
Keep away from foodstuffs, beverages and feed.
Immediately remove all soiled and contaminated clothing
Wash hands before breaks and at the end of work.
Avoid contact with the eyes and skin.
Personal protective equipment:
General protective and hygienic measures:
Keep away from foodstuffs, beverages and feed.
Immediately remove all soiled and contaminated clothing
Wash hands before breaks and at the end of work.
Avoid contact with the eyes and skin.
Respiratory protection:
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer
exposure use self+contained respiratory protective device.
Filter AX
In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer
exposure use self+contained respiratory protective device.
Filter AX
Protection of hands:
Wear gloves for the protection against chemical hazards according to EN 374.
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the
degradation.
Wear gloves for the protection against chemical hazards according to EN 374.
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the
degradation.
Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of
quality and varies from manufacturer to manufacturer. As the product is a preparation of several
substances, the resistance of the glove material can not be calculated in advance and has therefore to
be checked prior to the application.
The selection of the suitable gloves does not only depend on the material, but also on further marks of
quality and varies from manufacturer to manufacturer. As the product is a preparation of several
substances, the resistance of the glove material can not be calculated in advance and has therefore to
be checked prior to the application.
Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to
be observed.
Nitrile: Material thickness approximately 1.5 mm; min breakthrough time> 120
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to
be observed.
Nitrile: Material thickness approximately 1.5 mm; min breakthrough time> 120
Eye protection: Tightly sealed goggles
Body protection: Protective work clothing
Limitation and supervision of exposure into the environment
See section 6 and 12 for further information.
Limitation and supervision of exposure into the environment
See section 6 and 12 for further information.
9 Physical and chemical properties
Information on basic physical and chemical properties
General Information
Appearance:
General Information
Appearance:
Form:
Aerosol
Colour:
Different according to colouring
Odour:
Characteristic
Odour threshold:
Not determined.
pH<value:
Not determined.
Change in condition
Melting point/Melting range:
Undetermined.
Boiling point/Boiling range:
+24°C (dimethyl ether)
Flash point:
+42°C (dimethyl ether)
Flammability (solid, gaseous):
Not applicable.
(Contd. on page 6)
GB