Техническая Спецификация для Technoline RADIO CONTROLLED CLOCK WS 8001 02666 WS 8001

 

The time base for the radio controlled time is a Cesium Atomic Clock operated by the Physikalisch 
Technische Bundesanstalt Braunschweig which has a time deviation of less than one second in one 
million years. The time is coded and transmitted from Mainflingen near Frankfurt via frequency signal 
DCF-77 (77.5 kHz) and has a transmitting range of approximately 1,500 km. Your radio-controlled 
Moon Phase Clock receives this signal and converts it to show the precise time in summer or 
wintertime. The quality of the reception depends greatly on the geographic location. In normal cases, 
there should be no reception problems within a 1500km radius of Frankfurt.  

 

When the time code is received, the DCF tower becomes permanently lit and the time will be 
displayed. 
If the tower icon flashes, but does not set the time or the DCF tower does not appear at all, then 
please take note of the following: 
   

Recommended distance to any interfering sources like computer monitors or TV sets is a 
minimum of 1.5 - 2 meters. 

   

Within ferro-concrete rooms (basements, superstructures), the received signal is naturally 
weakened. In extreme cases, please place the unit close to a window and/ or point its front or 
back towards the Frankfurt transmitter. 

   

During nighttime, the atmospheric disturbances are usually less severe and reception is possible 
in most cases. A single daily reception is adequate to keep the accuracy deviation below 1 
second. 

 

Once the DCF time has been received, the date (day and month) , weekday, Moon phase and indoor 
temperature will be displayed accordingly. 

 

The date and weekday will be automatically displayed after the DCF time has been received.  

 

The Moon Phase Clock will display all 8 Moon phases throughout the year. 
  
 

 

 

New Moon       Waxing Crescent      First Quarter      Waxing Gibbous 

 
 

         

    

Full Moon 

    Waning Gibbous      Last Quarter     Waning Crescent 

 

The indoor temperature will be displayed and updated every 10 seconds. 
The seconds can be displayed when pressing the + key. To return to the indoor temperature display, 
press again the + key. 

By pressing and holding the SET key for about 1 second, the following settings can be changed. 
1. 

Time zone setting 

2. 

Language for weekday display setting 

3. 

Time setting (hour and minutes) 

4. 

Calendar setting (year, month, day and weekday)  

5. 

12 or 24 hour setting 

6. 

Temperature setting in °C (degrees Celsius) or °F (degrees Fahrenheit) 

 

The time zone can be be ajusted between ±12 hours. To change the time zone: 
1. 

Press the + key to set the time zone (default setting 0 hour) 

2. 

Using the SET key to move into the “Language setting” mode. To exit the programming mode, 
press the SNOOZE key anytime or wait around 15 seconds to automatically return to normal 
display mode. 

 

The weekday can be shown in seven different languages (D=German, GB=English, F=French,  
E=Spanish, I=Italian, NL=Dutch and DK=Danish), and every weekday is shown with 3 letters each 
(e.g. MON=Monday=Lundi), except for Dutch (only 2 letters).  
1. 

Press the + key to select the desired language. (default in “D” )  

2. 

Using the SET key to move into the “Time setting” mode. To exit the programming mode, press 
the SNOOZE key anytime or wait around 15 seconds to automatically return to normal display 
mode.

 

 

1. 

After entering into the time setting, the Hour digit in the time section starts flashing 

2. 

Press the + key to set the hours of the current time and then followed by pressing the SET key to 
move into the minutes mode. 

3. 

Again, press the + key to set the minutes of the current time (by holding the key down, the digits 
are incremented in steps of five). 

4. 

Press the SET key to enter the “Calendar setting” mode or do not touch any buttons for around 
15 seconds to confirm the time setting. To exit the programming mode, press the SNOOZE key 
anytime. The mode will return to normal.

 

 

1. 

The year digit starts flashing (default setting “00”) 

2. 

Press the + key to set the current year, (The range runs from 2000 to 2019, and only last 2 digits 
of the year will be displayed. e.g. 2000=00) and then followed by pressing the SET key to move 
into the month mode. 

3. 

Again, press the + key to set the current month and then followed by pressing the SET key to 
move into the date mode. 

4. 

Press the + key to set the current date and then followed by pressing the SET key to move into 
the weekday mode. 

5. 

Once again, press the + key to set the current weekday.  

6. 

Press the SET key to enter the “12/24 hour display setting” mode or do not touch any buttons for 
around 15 seconds to confirm the calendar setting. To exit the programming mode, press the 
SNOOZE key anytime. The mode will return to normal

 

 

The default time display for the clock is 24 hour, to select 12 hour display: 
1. 

“24” will start flashing on the LCD, press the + key to select “12” 

2. 

Press the SET key to enter the “Celsius or Fahrenheit degree setting” mode or do not touch any 
buttons for around 15 seconds to confirm the 12/24 hour display setting. To exit the 
programming mode, press the SNOOZE key anytime. The mode will return to normal.

 

 

Following from the 12/24 hour setting mode, the indoor temperature setting display can be changed. 
1. 

“°C” will appear on the LCD (default in “°C”). If “°C” is displayed then the current temperature 
reading is set to Celsius. If “°F” is displayed then the current temperature reading is set to 
Fahrenheit. 

2. 

To select the temperature setting, simply press the + key. 

3. 

Press SET key to confirm or do not touch any buttons for around 15 seconds or press the 
SNOOZE key to exit the programming mode anytime The mode will return to normal.

 

 

The maximum alarm duration is 80 seconds. To set the alarm function: