Справочник Пользователя для Jeti RC console 2.4 GHz No. of channels: 16 80001571
Модели
80001571
computer radio control system
EN
4.
4.
of these items you will enter the menu: „Select control input“, see
chapter 9.7. The assignments can easily be verified by the graphic
found beside the control element description in the „Trim “ section,
which shows the actual setup of the assigned control element.
The trim functions for the gimbal sticks P1-P4 are automatically
assigned to the quad push-buttons located below the gimbals.
It is not necessary to assign them manually.
chapter 9.7. The assignments can easily be verified by the graphic
found beside the control element description in the „Trim “ section,
which shows the actual setup of the assigned control element.
The trim functions for the gimbal sticks P1-P4 are automatically
assigned to the quad push-buttons located below the gimbals.
It is not necessary to assign them manually.
4.
Range of Additional Trim
If you set up a trim function, you can use the „Trim-Max“ to set the
maximum trim influence on the given flight function. The default
value is 50%. If you set the value to 0% the trim control element will
not have any effect on the flight function at all. If you set a value of
100%, the trim control element will control the flight function to its
full travel.
maximum trim influence on the given flight function. The default
value is 50%. If you set the value to 0% the trim control element will
not have any effect on the flight function at all. If you set a value of
100%, the trim control element will control the flight function to its
full travel.
5.
Adding a Function
With the „F3(New)“ button you can create (add) your own flight
function.
function.
6.
Deleting a Function
With the „F4(Delete)“ button you may delete the selected flight
function.
function.
Make sure that you have assigned all of your flight functions to the
correct transmitter control elements (stick, switch, knob or slider)
and make sure that the trims are assigned and functioning as you
wish. By pressing the „F5(Next)“ button you will enter the next
assistant step, the „Servo assignment “ menu.
correct transmitter control elements (stick, switch, knob or slider)
and make sure that the trims are assigned and functioning as you
wish. By pressing the „F5(Next)“ button you will enter the next
assistant step, the „Servo assignment “ menu.
The initial assignment is carried out in accordance with your
selected transmitter mode. If the initial assignment is incorrect
check the transmitter mode setup in the „Main menu->System-
>Configuration- >MODE 1-4 menu.
selected transmitter mode. If the initial assignment is incorrect
check the transmitter mode setup in the „Main menu->System-
>Configuration- >MODE 1-4 menu.
Note:
9.1. 8 Servo Assignment
This menu shows the assignment of transmitter output functions to
the receiver channels. This assignment can be changed as you wish.
The order number at the beginning of the column shows the
channel number and the assigned transmitter output function is
next to it. In this menu you can rearrange your output functions as
needed, i. e. any transmitter function can be assigned to any of the
receiver channels. The only restriction is the number of channels
which the transmitter can control (16 channels). The transmitter can
automatically set up your servo configuration based on your
previous model setup. If you want the transmitter to automatically
assign the servos in the same order as the last model that you set up,
press the „F3(Auto)“ button and then press the „F5(Yes)“ button.
the receiver channels. This assignment can be changed as you wish.
The order number at the beginning of the column shows the
channel number and the assigned transmitter output function is
next to it. In this menu you can rearrange your output functions as
needed, i. e. any transmitter function can be assigned to any of the
receiver channels. The only restriction is the number of channels
which the transmitter can control (16 channels). The transmitter can
automatically set up your servo configuration based on your
previous model setup. If you want the transmitter to automatically
assign the servos in the same order as the last model that you set up,
press the „F3(Auto)“ button and then press the „F5(Yes)“ button.
1
a)
42