Справочник Пользователя для Jeti RC console 2.4 GHz No. of channels: 16 80001571
Модели
80001571
computer radio control system
EN
4.
4.
1.
Editing a New Timer
a).
Timer Name
When you add or change the timer name, the name is automatically
displayed in that timer’s box on the main desktop.
displayed in that timer’s box on the main desktop.
b).
Initial Timer Value
This is where you can set the starting value for the timer. You can set
a negative or positve value for this starting point.
a negative or positve value for this starting point.
Target Timer Value
c).
Here is where you can set the target value for the timer. This can be
set as a positive value or a negative value. The initial value and target
value will determine the timer‘s direction. If the target value is
smaller than the initial value the timer will count down. If the target
value is larger than the initial value the timer will count up.
set as a positive value or a negative value. The initial value and target
value will determine the timer‘s direction. If the target value is
smaller than the initial value the timer will count down. If the target
value is larger than the initial value the timer will count up.
d).
Timer type
There are three possible timer types:
•
Standard – The timer starts or resumes when the chosen switch
is triggered and the timer pauses when the switch is turned off. The
timer’s value is not reset when the timer is paused. Use the
„F4(Stop)“ button to stop the timer.
timer’s value is not reset when the timer is paused. Use the
„F4(Stop)“ button to stop the timer.
•
Laps - The timer starts when the chosen switch is triggered.
Once the timer is started, each time the switch is triggered, the
elapsed time is stored in memory and the timer resets to your chosen
initial value. The lap number changes and the current lap time is
displayed each time the switch is triggered. Use the „F4(Stop)“
button to stop the timer. Then, you can use the „3D button“ to scroll
through the stored lap times.
elapsed time is stored in memory and the timer resets to your chosen
initial value. The lap number changes and the current lap time is
displayed each time the switch is triggered. Use the „F4(Stop)“
button to stop the timer. Then, you can use the „3D button“ to scroll
through the stored lap times.
•
Free-Running – The timer starts counting when the chosen
switch is triggered. Once started, this type of timer can only be
stopped using the „F4(Stop)“ button.
Use the „F5(Clr)“ button from the desktop to reset the timers.
stopped using the „F4(Stop)“ button.
Use the „F5(Clr)“ button from the desktop to reset the timers.
e).
Report type
You can use this item to select the type of audio alarm for the timer.
Some of the choices will create an audible warning which sounds
just before the target value is reached.
Some of the choices will create an audible warning which sounds
just before the target value is reached.
f).
Switch
This item is used to assign the switch or button to start the timer.
See chapter 9.7: „Select input control“.
See chapter 9.7: „Select input control“.
g).
Reset type
The „F5(Clr)“ button is used to reset the timers.
If you select „Short reset“ the timer is reset by a short press of the
„F5(Clr)“ button.
If you select „Long reset“ the timer is reset by a long press of the
„F5(Clr)“ button.
If you select „Short reset“ the timer is reset by a short press of the
„F5(Clr)“ button.
If you select „Long reset“ the timer is reset by a long press of the
„F5(Clr)“ button.
h).
Flight modes active
This item allows you to select which flight mode(s) for which the
timer is active.
timer is active.
While you are in the „Timer Detail“ menu the timer initial value is
displayed in the first function key position (bottom, left).
displayed in the first function key position (bottom, left).
70