Инструкции По Установке для White Rodgers 1F89-211 White-Rodgers 80 Series Heat Pump Thermostat

5

1

2

(SL)

FA

5

6

7

8

LOC

(OFF)

on

0 HI

(0)

4 LO to

4 HI

(F)

C

10

Select Compressor lockout OFF or ON

Select temperature display adjustment higher or lower

Select temperature display to F or C

4

d-L

(on)

OFF

Select display backlight OFF or ON

Filter

(000)

0 to 1950 hours

(in 50 hour increments)

Select filter replacement run time

Select FA or SL (Fast or Slow) pump cycle rate

3

EMER

(FA)

SL

Select FA or SL (Fast or Slow) Auxiliary and 
Emergency Aux heating cycle rate

and

and

and

9

FA

(on)

OFF

Select fast second-stage ON or OFF

and

and

and

and

and

Set SYSTEM

switch to OFF

SYSTEM switch must be OFF to configure thermostat options

Set SYSTEM switch 

to HEAT or COOL

Returns to normal operation

* Press          and

           to advance to next item

The configuration menu allows you to set certain thermostat 
operating characteristics to your system or personal require-
ments.
Move SYSTEM switch to the OFF position, then press

 and 

 and 

 to change to the next menu item. To exit 

the menu, move the SYSTEM switch to HEAT or COOL. If no
keys are pressed within fifteen minutes, the thermostat will exit
the configuration menu.

Rate - The FA setting is used to produce shorter heating cycles.
The SL setting produces a longer heating/cooling cycle. Both
settings produce very accurate temperature control and can be 
set to your personal preference. FA cycles the system just under
.75°F and the SL setting cycles at approximately 1.2°F.

Rate - The FA setting is frequently used for gas, oil or electric
heat. The SL setting produces a longer heating cycle. Both set-
tings produce very accurate temperature control and can be set 
to your personal preference. FA cycles the system just under
.6°F and the SL setting cycles at approximately 1.°F.

4) Select backlit display (d-L OFF or ON) - The display 

backlight improves display contrast in low lighting conditions.
Selecting backlight ON will keep the light on continuously.
Selecting OFF will keep the light off.

5)  Select filter replacement run time - The thermostat will 

display 

FILTER after a set time of operation. This is a re-

minder to change or clean your air filter. This time can be 
set from 0 to 1950 hours in 50 hour increments.

of 000 will cancel this feature. When FLTR is displayed, 
you can clear it by pressing 

 and 

 at the same time. 

This resets the timer and starts counting the hours until the 
next filter change. Contact your heat pump manufacturer for
a specific replacement/maintenance interval.

6)  Select Compressor Lockout (LOC OFF or ON) - Selecting

LOC ON will cause the thermostat to wait 5 minutes before

turning on the compressor if the heating and cooling system 
loses power. It will also wait 5 minutes minimum between cool-
ing cycles. This is intended to help protect the compressor from 
short cycling. Some newer compressors already have a time
delay built in and do not require this feature. Your compressor 
manufacturer can tell you if the feature is already present in 
their system. When the thermostat compressor time delay 
occurs it will flash the 

Snowflake or Flame icon for about 

five minutes. 

7)  Select Temperature Display Adjustment (4 LO to 4 HI) - 

Allows you to adjust the room temperature display up to 4°
higher or lower. Your thermostat was accurately calibrated 
at the factory but you have the option to change the display 
temperature to match your previous thermostat. The current 
or adjusted room temperature will be displayed on the right 
side of the display. 

8)  Select Temperature Display (°F or °C) - Changes the display

readout to Celsius or Fahrenheit as required. The current
room temperature will be displayed on the right side of the 
display. 

9)  Select Fast second stage - In the RUN mode, if the tem-

perature  is  manually  raised  by  3°F  (2°C)  or  more  above
room temperature using 

 and the fast second stage 

feature is enabled, FA on, the second stage will energize
immediately. With FA off, the second stage will not energize
until the setpoint temperature is 10°F or more above room
temperature.