Справочник Пользователя для Mitsubishi Electronics C64T
5. Base Specifications Parameters
15
5. Base Specifications Parameters
After setting up the parameter (PR) listed in the table, turn off the NC power. To validate the
parameter, turn on the power again.
parameter, turn on the power again.
# Items
Details
Setting range (unit)
1001
(PR)
SYS_ON
Part system
validation
setup
validation
setup
Specify the presence of the PLC axes and the 1st to
7th part systems with 1 or 0.
7th part systems with 1 or 0.
0: Not used
1: Used
1: Used
1002
(PR)
axisno Number
of
axes
Set No. of axes in each part system and the No. of PLC
axes.
Set so that the total of the NC axes and PLC axes is
less than the maximum number of controllable axes.
axes.
Set so that the total of the NC axes and PLC axes is
less than the maximum number of controllable axes.
0 to 14
1003
(PR)
iunit Input
setup
unit
Specify the input setting value for each part system
and the PLC axis. The parameter units will follow this
specification.
and the PLC axis. The parameter units will follow this
specification.
B: 1
µm
C: 0.1
µm
1013 axname Axis name
Specify each axis’ name address with an alphabetic
character.
Use the characters X‚ Y‚ Z‚ U‚ V‚ W‚ A‚ B or C.
Do not specify the same address in one part system.
The same address can be specified as the other part
system.
The PLC address does not need to be set. (The axis
name is displayed as 1 and 2.)
character.
Use the characters X‚ Y‚ Z‚ U‚ V‚ W‚ A‚ B or C.
Do not specify the same address in one part system.
The same address can be specified as the other part
system.
The PLC address does not need to be set. (The axis
name is displayed as 1 and 2.)
Axis addresses
such as X, Y, Z, U,
V, W, A, B, and C
such as X, Y, Z, U,
V, W, A, B, and C
1014 incax
Increment
command
axis name
command
axis name
When specifying the program movement rate’s
absolute or incremental method with an address‚
specify the incremental command axis name address
with an alphabetic character.
The address that can be used is the same as "#1013
axname".
Specify an address that is different from that #1013.
Setting is not required if absolute/incremental command
with addresses is not performed ("#1076 Abslnc" = 0).
absolute or incremental method with an address‚
specify the incremental command axis name address
with an alphabetic character.
The address that can be used is the same as "#1013
axname".
Specify an address that is different from that #1013.
Setting is not required if absolute/incremental command
with addresses is not performed ("#1076 Abslnc" = 0).
1015
(PR)
cunit Command
unit
Specify the minimum unit of the program movement
amount.
cunit
amount.
cunit
Movement amount for movement command 1
10: 0.001 mm ( 1
µm)
100: 0.01 mm ( 10
µm)
1000: 0.1
mm (100
µm)
10000: 1.0
mm
If there is a decimal point in the movement command‚
the decimal point position will be handled as 1mm
regardless of this setting.
the decimal point position will be handled as 1mm
regardless of this setting.
10
1
µm
100
10
µm
1000
100
µm
10000 1
mm
1016
(PR)
iout
Inch output
Specify whether the machine system (ball screw pitch‚
position detection unit) is an inch unit system or metric
unit system.
position detection unit) is an inch unit system or metric
unit system.
0: Metric unit
system
1: Inch unit system
system
1: Inch unit system