Справочник Пользователя для Toastmaster A710P

ENGLISH

FRANÇAIS

PAÑOL

B. Operation Procedure

If necessary, adjust the closure height of the top grill plate as

described below. Refer to Figure 3.

Check that the top grill plate is lowered.

Loosen the closure height locking knob.

Turn the closure height adjustment knob as necessary to

raise or lower the top grill plate to the correct height. See

Figure 3.
-

Turn the knob clockwise to raise the top grill.

Turn the knob counterclockwise to lower the top grill.

If necessary, place a sample of the food product between

the grill plates to check for the correct spacing.

When the top grill plate is at the proper height, tighten the

closure height locking knob.

II. INSTALLATION

IMPORTANT

IT IS THE CUSTOMERS RESPONSIBILITY TO REPORT ANY

CONCEALED OR NON-CONCEALED DAMAGE TO THE FREIGHT

COMPANY.
A. Placement
Check that the four 5/8 (16mm) rubber feet are installed. Then,

position the sandwich grill in place.
B. Initial Cleaning
1.

Ensure that any packing material has been removed.

Follow the procedure in Section IV, Daily Cleaning, to perform

an initial cleaning of the grill. Be sure to thoroughly clean the top

and bottom grill plates, AND the exterior of the grill.

If your grill is has grill plates with a natural aluminum finish,

condition the grills with a thin coating of cooking oil or shortening.

If your grill has a DuPont SilverStone Supra® coating, it is not

necessary to season the non-stick surface.

C. Electrical Utility Connection
IMPORTANT

THE ELECTRICAL CONNECTION TO THE SANDWICH GRILL RE-

QUIRES A CIRCUIT BREAKER/FUSED DISCONNECT. ELECTRI-

CAL SPECIFICATIONS ARE LISTED ON THE SERIAL PLATE (LO-

CATED ON THE REAR OF THE SANDWICH GRILL), AND ON THE

WIRING DIAGRAMS AT THE BACK OF THIS MANUAL.
CONSULT ALL APPLICABLE NATIONAL AND LOCAL CODES FOR

FURTHER ELECTRICAL CONNECTION REQUIREMENTS.
1.

Before proceeding with the electrical connection, check the fol-

lowing:
a.

Check that the electrical supply matches the sandwich grills

requirements. Refer to the serial plate (on the rear of the

unit) and to the electrical specifications at the back of this

Manual.

Check that the appropriate receptacle is available for the

power cord plug.

WARNING

ENSURE THAT BOTH THE CIRCUIT BREAKER/FUSED DIS-

CONNECT AND THE THREE-POSITION POWER SWITCH

ARE IN THE OFF (O) POSITION BEFORE PROCEEDING.
WARNING

ENSURE THAT ANY PACKING MATERIAL HAS BEEN RE-

MOVED FROM THE TOP AND BOTTOM GRILL PLATES.

Insert the power cord plug into its receptacle.

III. OPERATION

A. Location and Function of Controls
This section provides a basic description of the sandwich grills controls,

their location, and the functions they perform. The operator MUST be

familiar with the controls. See Figure 2.

Closure height adjustment knob

Adjusts the spacing between the top and bottom grill plates to

accomodate food products of different thicknesses.

Closure height locking knob

When tightened, prevents the Closure Height Adjustment Knob

from being turned. When loosened, allows the Closure Height

Adjustment Knob to be turned.

Temperature adjustment knob

Adjusts the temperature setting of the heating element(s). This

controls the temperature of the grill plates.
To change the temperature setting, turn the knob until the desired

temperature is aligned with the arrow above the knob.

Three-position power switch

When set to ON

BOTTOM

GRID

, turns on the heating element

for the bottom grill plate ONLY.

When set to OFF (O), turns off both of the heating

elements.

When set to ON

TOP

BOTTOM

GRIDS

, turns on the heating

elements for the top AND bottom grill plates.

Figure 2

1. Closure height

adjustment knob

2. Closure

height

locking

knob

3. Temperature

adjustment knob

4. BOTH/OFF/

BOTTOM switch

Figure 3

Loosen

locking knob

Turn adjustment knob

to reposition top grill

Raise

grill

Lower

grill

Tighten

locking knob

Check that top

grill plate is

lowered