Справочник Пользователя для Intelligent Motion Systems 17
11
S e c t i o n 1 . 3
I n t r o d u c t i o n t o t h e M D r i v e 2 3 M o t i o n C o n t r o l
I n t r o d u c t i o n t o t h e M D r i v e 2 3 M o t i o n C o n t r o l
The MDrive23 Motion Control offers the system designer a low-cost, intelligent motion controller integrated with a NEMA 23 high
torque stepping motor and a +12 to +48 VDC microstepping drive.
torque stepping motor and a +12 to +48 VDC microstepping drive.
The MDrive23 Motion Control adds a versatile array of functions by combining a complete programmable motion controller with
our already compact and cost effective standard MDrive23, adding little cost and no increase in size. Standard offerings include four
5 to 24 volt programmable I/O points, one 10-bit 0 to 5 volt analog input, 0 to 5 MHz step clock rate, microstep resolution up to
51,200 steps per revolution and a full featured easy-to-program instruction set.
our already compact and cost effective standard MDrive23, adding little cost and no increase in size. Standard offerings include four
5 to 24 volt programmable I/O points, one 10-bit 0 to 5 volt analog input, 0 to 5 MHz step clock rate, microstep resolution up to
51,200 steps per revolution and a full featured easy-to-program instruction set.
The MDrive23 Motion Control communicates using the RS-485 communications protocol, this allows for point-to-point or multi-
drop communications using one communications port. Addressing and hardware support up to 62 MDrive nodes in a system. The
communications BAUD rate is software selectable and ranges from 4.8 kbps to 115 kbps.
drop communications using one communications port. Addressing and hardware support up to 62 MDrive nodes in a system. The
communications BAUD rate is software selectable and ranges from 4.8 kbps to 115 kbps.
The MDrive23 is also available with an optional closed loop control. The closed loop configuration adds a 512 line (2048 count)
internal magnetic rotary encoder with index mark without increasing the length of the unit. Closed loop configuration adds position
maintenance, stall detection and find index mark.
internal magnetic rotary encoder with index mark without increasing the length of the unit. Closed loop configuration adds position
maintenance, stall detection and find index mark.
Available motor configurations include: single shaft, double shaft with control knob, and long life ACME screw linear actuator.
Rotary versions are available in three stack lengths: 18, 22 & 31. Interface connections are accomplished using either a 7 position
terminal block or optional 12” flying leads.
Rotary versions are available in three stack lengths: 18, 22 & 31. Interface connections are accomplished using either a 7 position
terminal block or optional 12” flying leads.
F e a t u r e S u m m a r y
!
Integrated Microstepping Drive/Motion Controller with Optional Encoder/NEMA 23 High Torque Stepping Motor
!
+12 to +48VDC Input Voltage
!
Low Cost
!
Extremely Compact
!
Available Configurations: Single Shaft*, Linear Actuator, Integral Encoder*, Double Shaft with Knob for Manual
Positioning*
Positioning*
!
Three Motor Stack Lengths Available*
!
Single Power Supply
!
Microstep Resolution up to 51,200 Steps Per Revolution
!
Open Loop or Optional Closed Loop Control
!
Programmable Motor Run and Hold Current Settings
!
Four 5 to 24 VDC Programmable I/O Points
!
One Analog 10 Bit, 0 to 5 Volt Analog Input
!
0 to 5 MHz Step Clock Rate, Selectable in 0.59 Hz Increments
!
RS-485 Communications Protocol
!
Communications BAUD Rate Selectable from 4.8 kbps to 115 kbps
!
62 Software Addresses for Multidrop Communications
!
Simple 1 and 2 Character Programming Instructions
!
Pluggable Terminal Strip or 12” Flying Lead Interface
!
Optional Integrated RS-232 to RS-485 Converter/Communications Cable
*Rotary Motor Only