Справочник Пользователя для RCA SPS36073
10
MOUNTiNG iNSTRUCTiONS
b) Fold the Mounting Template along the guideline
that is closest to the thickness of your cabinet
overhang.
overhang.
c) Tape Mounting Template to the underside of the
cabinet with the folded portion of the Mounting
Template flush up against the cabinet overhang
(see Figure 2). Go to
Template flush up against the cabinet overhang
(see Figure 2). Go to
STEP 2.
If your cabinet
DOES have an overhang:
a) Measure the thickness “T” of the cabinet
overhang (see Figure 1).
Front
Edge
Edge
Front
Edge
Edge
STEP 1
If your cabinet does
NOT have an overhang:
a) Place the Mounting Template in the desired
location inside or underneath the cabinet
(whichever has less obstructions, and will be
easier for you to reach to drill holes), flush with
the front edge of the cabinet and tape it down.
Go to
(whichever has less obstructions, and will be
easier for you to reach to drill holes), flush with
the front edge of the cabinet and tape it down.
Go to
STEP 2.
STEP 2
Use an electric drill with a ¼” drill bit (not included) to
drill all four holes marked on the Mounting Template
(see Figure 3). To reduce splintering, place a small
piece of masking tape over each hole location before
drilling. Go to
Use an electric drill with a ¼” drill bit (not included) to
drill all four holes marked on the Mounting Template
(see Figure 3). To reduce splintering, place a small
piece of masking tape over each hole location before
drilling. Go to
STEP 3.
If your cabinet
DOES have an overhang:
a) Four screws are included with this unit. Make
sure the screws will go completely through your
cabinet bottom, and extend at least 3/8” past the
bottom of your cabinet overhang.
cabinet bottom, and extend at least 3/8” past the
bottom of your cabinet overhang.
b) This unit includes two sets of four spacers of
different length. The spacers can be put together
to form longer spacers to accommodate various
cabinet overhang thicknesses. Determine the
best combination of spacers which is equal to or
longer than the cabinet overhang thickness.
to form longer spacers to accommodate various
cabinet overhang thicknesses. Determine the
best combination of spacers which is equal to or
longer than the cabinet overhang thickness.
c) Hold the unit up against the bottom of the cabinet,
and align the four holes on the top of the unit with
the screws. Partially tighten each screw, but do
not fully tighten the screws until all of them have
been started.
the screws. Partially tighten each screw, but do
not fully tighten the screws until all of them have
been started.
d) Gently tighten each screw until they are firmly
holding the unit in place.
(Continued on next page)
STEP 3
If your cabinet does
NOT have an overhang:
a) Eight screws are included with this unit, but you
will only need four of them. Select the screw
length which will go completely through your
cabinet bottom, and provide at least 3/8” of thread
to screw into the main unit.
length which will go completely through your
cabinet bottom, and provide at least 3/8” of thread
to screw into the main unit.
b) Insert the four selected screws through each hole
from the inside of the cabinet going down (see
Figure 4).
Figure 4).
Figure 1
Figure 2
Figure 4
TOOLS NEEDED: 1) Electric drill with 1/4” bit; 2) Phillips-head (cross style) screwdriver.
T
Cabinet Bottom
Mounting
Screw
Template
Template
Figure 3
RCA SPS36073 English IB W012 OK.indd 11
8/21/2009 4:47:45 PM