Справочник ПользователяСодержаниеTL260GS / TL265GS1TL260GS / TL265GS1Installation Manual1Limited Warranty2International Warranty2Warranty Procedure2Conditions to Void Warranty2Items Not Covered by Warranty2Disclaimer of Warranties3Out of Warranty Repairs3WARNING4Note to Installers4System Failures4Criminal Knowledge4Access by Intruders4Power Failure4Failure of Replaceable Batteries4Compromise of Radio Frequency (Wireless) Devices4Smoke Detectors4Motion Detectors5Warning Devices5Telephone Lines5Insufficient Time5Component Failure5Inadequate Testing5Security and Insurance5Warning6FCC6Industry Canada Statement6IMPORTANT - READ CAREFULLY:7Introduction101 . On your hard drive, locate the laptop’s IP address. Retrieve the number of the listening port; this is assigned by the application. You should also have on hand the Communicator’s phone number.102 . Using this phone number send the Communicator an 18-digit SMS text message. This SMS text message is to be configured as: ! + IP address + Port number, without stops or spaces (e.g. !11122233344412345). Note that if you intend to use a port numbe...103 . With an existing installation of DLS IV downloading software on your laptop, you now have the ability to program the Communicator using the GUI on the screen. See Options on page 23 for detailed programming information. Also, please refer to your...10Models10Features10Technical Specifications11Ratings12Table 1: Communicator Ratings12Compatibility13Table 2: Compatible Receivers and Control Panels13Table 2: Compatible Receivers and Control Panels13INSTALLING THE GSM / ETHERNET COMMUNICATOR141 . Wire the telephone line, if available.142 . Wire the PC9155 panel (but not the Communicator).143 . Turn on the PC9155 panel. Program the panel’s telephone number, account code, format, GS / IP module enable, and the communication path priority (i.e. PSTN > Ethernet > GRPS).144 . Turn off the panel.145 . Wire the Communicator through the PC-Link.146 . Proceed to CONNECT 24 Activation Information below.147 . Turn on the panel. Wait for the initialization of the Communicator.141 . Assemble the Communicator142 . Install the Communicator module into the Cabinet153 . Turn on the panel and check signal strength.151 . Attach the Communicator to the inside of the PC9155 control panel cabinet if not already present.162 . Turn on the PC9155 cabinet and check signal strength.171 . Program the hexadecimal digits (DCAA) in the telephone number that will be used to contact the GSM / Ethernet Communicator (panel Options 301, 302, 303, ‘Telephone Phone Number Programming’).182 . In Option 350, program the communication format as SIA FSK.183 . In Options 351 through Option 376, program the call direction sub-options for the phone number being used to communicate using the GSM / Ethernet Communicator.184 . Option 382, sub-option 5 must be set to ON.18STATUS LEDs19Trouble Status LED19Table 3: Trouble Status LED19Network Connection Status LED21Signal Strength LEDs21Table 4: Radio Signal Strength211 . Turn off the power to the Communicator by physically unplugging the unit from its power supply.212 . Attach one end of the extension cable to the Communicator and the other end to the antenna itself.213 . Reattach the power supply and turn on.214 . Move the antenna around until you have received a strong signal.215 . Mount the antenna bracket at that location.211 . Locate the set of five vertically aligned pins in the middle of the Communicator board.212 . Counting from the bottom, the first three pins are reserved for future use. You may discount these.213 . The final two pins require a jumper in order to reset the hardware values.214 . Turn off power to the Communicator.215 . Apply the jumper to the two pins.226 . Turn on power to the Communicator. Wait for ten seconds.227 . Remove the jumper from the pins.22Table 5: Communicator Troubles on a 9155 Panel22Options24System Options24Table 6: Window Times25Table 7: System Toggle Options25GPRS Options29System Information29Programming Worksheets30Размер: 866,0 КБСтраницы: 33Язык: EnglishПросмотреть
