Инструкции для Hitachi SJ300-037HFE

Hitachi

Справочник Пользователя (English)

Справочник Пользователя

Содержание

Cover
1
Safety Messages
2
Table of Contents
16
- Revisions
  18
- Contact Information
  19
Getting Started
20
Inverter Mounting and Installation
38
Configuring Drive Parameters
68
Operations and Monitoring
137
- Introduction
  138
  - Cautions for Operating Procedures
    138
  - Warnings for Operating Procedures
    139
- Optional Controlled Decel and Alarm at Power Loss
  140
- Connecting to PLCs and Other Devices
  143
- Using Intelligent Input Terminals
  147
  - Input Wiring Examples
    147
  - Wiring Diagram Conventions
    148
  - Forward Run/ Stop and Reverse Run/Stop Commands
    148
  - Multi-Speed Select
    149
  - Jogging Command
    152
  - External Signal for DC Injection Braking
    153
  - Set Second or Third Motors
    154
  - Two-stage Acceleration and Deceleration
    155
  - Free-run Stop
    156
  - External Trip
    157
  - Unattended Start Protection
    158
  - Commercial Power Source Switching
    159
  - Software Lock
    161
  - Analog Input Current/Voltage Select
    162
  - Reset Inverter
    163
  - Thermistor Thermal Protection
    164
  - Three-wire Interface Operation
    165
  - PID ON/OFF and PID Clear
    166
  - Internal Speed Loop Gain Settings
    167
  - Remote Control Up and Down Functions
    169
  - Force Operation from Digital Operator
    170
  - Overload Restriction
    171
  - Torque Limit
    173
  - External Brake Control Function
    175
  - Expansion Card Input Signals
    177
- Using Intelligent Output Terminals
  178
  - Run Signal
    179
  - Frequency Arrival Signals
    180
  - Overload Advance Notice Signal
    182
  - Output Deviation for PID Control
    183
  - Alarm Signal
    184
  - Over-torque Signal
    186
  - Instantaneous Power Failure / Under-voltage Signal
    187
  - Torque Limit Signal
    190
  - Run Time / Power-On Time Over Signals
    190
  - Thermal Warning Signal
    191
  - Brake Control Signals
    194
  - Expansion Card Output Signals
    194
- Analog Input Operation
  195
  - Input Terminal Signals
    195
  - Input Filter
    195
  - Wiring Examples
    197
- Analog Output Operation
  198
  - [FM] Terminal
    198
  - PWM Signal Type
    198
  - FM Signal Type
    199
  - [AM] and [AMI] Terminals
    200
- Setting Motor Constants for Vector Control
  201
  - Introduction
    201
  - Auto-tuning of Motor Constants
    203
  - Auto-tuning Procedure
    204
  - Adaptive Auto- tuning of Motor Constants
    205
  - Manual Setting of Motor Constants
    206
- PID Loop Operation
  207
- Configuring the Inverter for Multiple Motors
  208
  - Simultaneous Connections
    208
  - Inverter Configuration for Multiple Motor Types
    208
Inverter System Accessories
210
- Introduction
  211
- Component Descriptions
  212
  - AC Reactors, Input Side
    212
  - AC Reactor or LCR Filter, Output Side
    212
  - Zero-phase Reactor (RF Noise Filter)
    213
  - EMI Filter
    213
  - Ferrite Core
    213
  - RF Noise Filter (Capacitive)
    213
  - DC Link Choke
    213
  - Expansion Cards
    214
- Dynamic Braking
  215
  - Introduction
    215
  - Dynamic Braking Usage Ratio
    215
  - SJ300 Dynamic Braking Selection Tables
    216
  - Choosing a Braking Unit
    217
  - Selecting a Braking Resistor
    218
Troubleshooting and Maintenance
222
- Troubleshooting
  223
  - Safety Messages
    223
  - General Precautions and Notes
    223
  - Inspection Items
    223
  - Troubleshooting Tips
    224
- Monitoring Trip Events, History, & Conditions
  226
  - Fault Detection and Clearing
    226
  - Error Status Codes
    226
  - Error Codes
    226
  - Trip History and Inverter Status
    229
- Restoring Factory Default Settings
  230
- Maintenance and Inspection
  231
  - Monthly and Yearly Inspection Chart
    231
  - Megger Test
    232
  - Spare parts
    233
  - Capacitor Life Curve
    233
  - Capacitor Replacement
    234
  - Fan Assembly Replacement
    235
  - General Inverter Electrical Measurements
    236
  - Inverter Output Voltage Measurement Techniques
    237
  - IGBT Test Method
    238
- Warranty
  239
  - Warranty Terms
    239
Glossary and Bibliography
240
- Glossary
  241
- Bibliography
  245
Serial Communications
246
- Introduction
  247
  - Serial Connection Diagrams
    248
  - Serial Network Parameter Settings
    249
- Communications Protocol
  250
  - Introduction to Command List
    250
  - Command - 00
    251
  - Command - 01
    251
  - Command - 02
    252
  - Command - 03
    253
  - Command - 04
    255
  - Command - 05
    256
  - Command - 06
    258
  - Command - 07
    259
  - Command - 08
    260
  - Command - 09
    260
  - Command - 0A
    261
  - Command - 0B
    261
- Communications Reference Information
  262
  - Inverter Affirmative Reply
    262
  - Inverter Negative Reply
    262
  - Block Check Code (BCC)
    263
  - ASCII Code Table
    263
  - Communication Test Mode
    264
Drive Parameter Settings Tables
265
- Introduction
  266
- Parameter Settings for Keypad Entry
  266
  - Main Profile Parameters
    266
  - Standard Functions
    267
  - Fine Tuning Functions
    271
  - Intelligent Terminal Functions
    274
  - Motor Constants Functions
    277
  - Expansion Card Functions
    279
  - User-selectable Menu Functions
    280
CE-EMC Installation Guidelines
281
- CE-EMC Installation Guidelines
  282
- Hitachi EMC Recommendations
  284
Index
285
- A
  285
- B
  285
- C
  285
- D
  286
- E
  286
- F
  286
- G
  286
- H
  286
- I
  287
- J
  287
- K
  287
- L
  287
- M
  287
- N
  287
- O
  287
- P
  288
- R
  288
- S
  288
- T
  289
- U
  289
- V
  289
- W
  289
- Z
  289

Справочник Пользователя

Размер:

7,1 МБ
Страницы:

289
Язык:

English

Просмотреть