Справочник ПользователяСодержаниеImportant Safety Instructions31. Read these instructions.32. Keep these instructions.33. Heed all warnings.34. Follow all instructions.35. Only use attachments/accessories specified by the manufacturer.36. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.37. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, suc...38. Installation should be done only by qualified personnel and conform to all local codes.39. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.310. Use only installation methods and materials capable of supporting four times the maximum specified load.311. Use stainless steel hardware to fasten the mount to outdoor surfaces.312. AN ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building.313. Only use replacement parts recommended by Pelco.314. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualified to do so.3Description4Models4Installation5Figure 1. Package Contents5Figure 2. Exploded View of EH3500 Series Assembly61. Unlatch and open the lid.72. Remove the camera sled from the rail of the enclosure.7a. Loosen the screws that hold the camera sled in place.7b. Slide the sled forward so it can be lifted out over the screws.7c. Remove the sled.7d. Remove the parts bag tied to the sled. This includes the hex head screws, flat washers, split washers, glands, and nuts.73. If you are wiring the enclosure with cable, remove the glands and nuts from the parts bag and install them in the bottom of the enclosure. If you are wiring the enclosure with conduit, do not install the glands.74. Attach the enclosure body to the appropriate mount using the instructions provided with the mount.75. Attach the camera to the sled with the 1/4-20 x 0.375-inch Phillips screws provided (in the parts bag). You can attach the ca...76. Move the sled so that the sled mounting screws extend through the narrow part of sled mounting holes, and partially tighten the sled mounting screws.77. Pull the video and power cables through the glands or conduit on the bottom of the enclosure. Refer to Tables A and B to determine the size of power wire to use. Refer to Table C for the type of video coaxial cable to use.78. Attach the cables to the camera.79. If the enclosure has accessories that require power, you will need to access the PC board. To remove the cover, insert a screwdriver into the slot on top of the cover and lift the cover off.8Figure 3. Accessing the PC Board810. If the camera lens is adjustable, extend the lens to its maximum length; verify that the camera is adjusted with the lens a minimum of 1/2 inch from the enclosure window.811. Tighten the screws that secure the sled to the enclosure.812. Adjust the glands for a tight fit around the cables.813. Close the enclosure lid, and latch.814. Adjust the camera focus and iris if necessary. If you need to adjust the focus and iris manually, open the enclosure lid, adjust the focus and iris, and close the enclosure lid.8Figure 4. EH3508-1/-2/-3 Wiring Diagram9Figure 5. EH3512 Series Wiring Diagram10Figure 6. EH3515 Series Wiring Diagram11Table A. Enclosure Accessory Wiring Distances12Table A. Enclosure Accessory Wiring Distances (Continued)13Table B. 24 VAC Wiring Distances14Table C. Video Coaxial Cable Wiring Distances14Operation15Maintenance15Service Manual15Specifications16General16Figure 7. EH3508, EH3512, EH3515 Dimension Drawing17Размер: 626,7 КБСтраницы: 20Язык: EnglishПросмотреть
Справочник ПользователяСодержаниеImportant Safety Instructions31. Read these instructions.32. Keep these instructions.33. Heed all warnings.34. Follow all instructions.35. Only use attachments/accessories specified by the manufacturer.36. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.37. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, suc...38. Installation should be done only by qualified personnel and conform to all local codes.39. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture.310. Use only installation methods and materials capable of supporting four times the maximum specified load.311. Use stainless steel hardware to fasten the mount to outdoor surfaces.312. AN ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm in each pole shall be incorporated in the electrical installation of the building.313. Only use replacement parts recommended by Pelco.314. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other that contained in the operating instructions unless you are qualified to do so.3Description4Models4Installation5Figure 1. Package Contents5Figure 2. Exploded View of EH3500 Series Assembly61. Unlatch and open the lid.72. Remove the camera sled from the rail of the enclosure.7a. Loosen the screws that hold the camera sled in place.7b. Slide the sled forward so it can be lifted out over the screws.7c. Remove the sled.7d. Remove the parts bag tied to the sled. This includes the hex head screws, flat washers, split washers, glands, and nuts.73. If you are wiring the enclosure with cable, remove the glands and nuts from the parts bag and install them in the bottom of the enclosure. If you are wiring the enclosure with conduit, do not install the glands.74. Attach the enclosure body to the appropriate mount using the instructions provided with the mount.75. Attach the camera to the sled with the 1/4-20 x 0.375-inch Phillips screws provided (in the parts bag). You can attach the ca...76. Move the sled so that the sled mounting screws extend through the narrow part of sled mounting holes, and partially tighten the sled mounting screws.77. Pull the video and power cables through the glands or conduit on the bottom of the enclosure. Refer to Tables A and B to determine the size of power wire to use. Refer to Table C for the type of video coaxial cable to use.78. Attach the cables to the camera.79. If the enclosure has accessories that require power, you will need to access the PC board. To remove the cover, insert a screwdriver into the slot on top of the cover and lift the cover off.8Figure 3. Accessing the PC Board810. If the camera lens is adjustable, extend the lens to its maximum length; verify that the camera is adjusted with the lens a minimum of 1/2 inch from the enclosure window.811. Tighten the screws that secure the sled to the enclosure.812. Adjust the glands for a tight fit around the cables.813. Close the enclosure lid, and latch.814. Adjust the camera focus and iris if necessary. If you need to adjust the focus and iris manually, open the enclosure lid, adjust the focus and iris, and close the enclosure lid.8Figure 4. EH3508-1/-2/-3 Wiring Diagram9Figure 5. EH3512 Series Wiring Diagram10Figure 6. EH3515 Series Wiring Diagram11Table A. Enclosure Accessory Wiring Distances12Table A. Enclosure Accessory Wiring Distances (Continued)13Table B. 24 VAC Wiring Distances14Table C. Video Coaxial Cable Wiring Distances14Operation15Maintenance15Service Manual15Specifications16General16Figure 7. EH3508, EH3512, EH3515 Dimension Drawing17Размер: 626,7 КБСтраницы: 20Язык: EnglishПросмотреть
