Roland AR-3000R 用户手册
15
Panel Descriptions
8. LINE IN Jack
This is used when recording audio from a device equipped with
an analog audio-output jack.
an analog audio-output jack.
9. Audio Output Jacks (BALANCED OUTPUT)
These are the final audio output jacks. They are used for
connection to a power amp or the like. Both balanced and
unbalanced connections are possible.
connection to a power amp or the like. Both balanced and
unbalanced connections are possible.
922
* This instrument is equipped with balanced (TRS) type jacks.
Wiring diagrams for these jacks are shown below. Make
connections after first checking the wiring diagrams of other
equipment you intend to connect.
connections after first checking the wiring diagrams of other
equipment you intend to connect.
fig.2-05e
926a
When connection cables with resistors are used, the volume
level of equipment connected to the inputs (LINE IN Jack)
may be low. If this happens, use connection cables that do
not contain resistors, such as those from the Roland PCS
series.
level of equipment connected to the inputs (LINE IN Jack)
may be low. If this happens, use connection cables that do
not contain resistors, such as those from the Roland PCS
series.
10. Option Board Slot
This is the recess for installing an option board.
→
“Installing an Option board”
When installing, be sure to refer to the owner’s manual for
the option board.
the option board.
11. Option Board Space
This is where an option board is installed.
→
“Installing an Option board”
When installing, be sure to refer to the owner’s manual for
the respective option board.
the respective option board.
12. Rubber Feet (Included Items)
→
Installing an Option Board
When installing, be sure refer to the owner’s manual for the
respective option board.
respective option board.
fig.2-06e
Important Notes on Installation
●
Before installing the board, switch off the power to the
equipment and unplug the power cord from the power outlet.
●
Remove only the specified screws.
●
Be careful not to let removed screws fall into the unit.
●
After you have removed the panel, cover, and screws, do not
leave them off. When you have finished installing the option
board, be sure to reattach the panel, cover, and screws.
board, be sure to reattach the panel, cover, and screws.
●
Be careful not to cut your hand on the opening for installing the
board.
●
After installation, if the unit fails to power up when you switch
on the power, contact your Roland Service Station.
●
To avoid the risk of damage to internal components that can be
caused by static electricity, please carefully observe the
following whenever you handle the board.
caused by static electricity, please carefully observe the
following whenever you handle the board.
•
Before you handle the circuit board, first touch the front panel
of the AR-3000R, and while maintaining contact with the front
panel, pick up the circuit board. This discharges any static
electricity that has accumulated in your body and clothing.
of the AR-3000R, and while maintaining contact with the front
panel, pick up the circuit board. This discharges any static
electricity that has accumulated in your body and clothing.
•
When handling the board, grasp it only by the panel or the
board’s edges. Avoid touching any of the electronic
components or connectors.
board’s edges. Avoid touching any of the electronic
components or connectors.
•
When handling the board, grasp it only by the panel or
the board’s edges. Avoid touching any of the electronic
components or connectors.
the board’s edges. Avoid touching any of the electronic
components or connectors.
•
Before you connect any cables, make sure they do not
carry a static electricity charge. Such charges can be
carry a static electricity charge. Such charges can be
GND(SLEEVE)
HOT(TIP)
COLD(RING)
Balanced Output
GND(SLEEVE)
HOT(TIP)
Unbalanced Output
Rear Panel
Top Panel
Removed screws
Option board
901
AR-3000R_e.book 15 ページ ２０１０年３月１８日 木曜日 午後２時６分