Roland AR-3000R 用户手册
92
Controlling the AR-3000R from an External Device
Registering Phrases
Register the phrases in the program playback order. Up to a
maximum of 100 phrases can be registered in each of the five
patterns of Programs 1 through 5.
maximum of 100 phrases can be registered in each of the five
patterns of Programs 1 through 5.
While you can select phrases from Card A as well as Card B,
note that playback will not work properly if the card inserted
when the phrase was registered is not inserted at the time of
playback (if the phrase is not saved, the next phrase is sought
and then played back).
note that playback will not work properly if the card inserted
when the phrase was registered is not inserted at the time of
playback (if the phrase is not saved, the next phrase is sought
and then played back).
Settings When Formatting Cards (in Slot A)
fig.14-22e
Procedure for Registering Phrases
1.
Press the MODE button.
The MODE indicator lights up.
2.
Use the SELECT dial to choose “5.3 Program Playback,”
then press the dial.
then press the dial.
3.
Turn the SELECT dial to choose the Program No. where
you want to make the setting (1 through 5), then press
the dial.
you want to make the setting (1 through 5), then press
the dial.
fig.14-g07e
4.
Turn the SELECT dial to choose the playback sequence,
then press the dial.
then press the dial.
•
Nos. 001-100:
Playback order
•
END:
Finishes the setting process.
•
RESET:
Restores the settings the card had when
formatted.
•
CLEAR:
Erases all settings.
5.
Turn the SELECT dial to choose the card containing the
phrase you want to store, then press the dial.
phrase you want to store, then press the dial.
fig.14-g08e
6.
Turn the SELECT dial to choose the phrase you want to
store, then press the dial.
store, then press the dial.
7.
Repeat steps 4 and 5 to store more phrases.
8.
To cancel the save process, then in step 4, turn the
SELECT dial to choose “END,” then press the dial.
SELECT dial to choose “END,” then press the dial.
fig.14-g09e
9.
When the prompt appears on the screen, press the
ENTER button to enable the settings.
ENTER button to enable the settings.
To quit without making the settings, use the SELECT dial to
choose “NO,” then press the ENTER button.
choose “NO,” then press the ENTER button.
Once the settings have been made successfully, you’re
returned to the setting item selection screen.
returned to the setting item selection screen.
10.
Press the MODE button.
This ends the setting process and returns you to the usual
screen.
screen.
* While making the settings, you can go back to the previous
entry position (highlighted) by using the PAUSE (BACK)
button.
button.
* If you press the MODE button while making settings, a
message asking you to confirm that you want to exit the
setting process appears. Note that if you choose “YES,” then
press the ENTER button, you are returned to the usual screen,
and all setting changes you’ve made up to that point will be
discarded.
setting process appears. Note that if you choose “YES,” then
press the ENTER button, you are returned to the usual screen,
and all setting changes you’ve made up to that point will be
discarded.
Specifying Phrase Numbers
in Binary Notation (Binary
in Binary Notation (Binary
Playback)
What is Binary Playback?/Uses
and Applications
and Applications
In binary playback, phrases are selected by means of binary
(Base 2) control signal input to the Port No. 1 through 11,
with the selected phrases played back when control signals
are input to the START port. You can select and play back up
to a maximum of 2000 phrases.
(Base 2) control signal input to the Port No. 1 through 11,
with the selected phrases played back when control signals
are input to the START port. You can select and play back up
to a maximum of 2000 phrases.
This allows all phrases to be specified with control signals
(from a switch or other ON/OFF signal device) without the
use of computers or other complicated equipment.
(from a switch or other ON/OFF signal device) without the
use of computers or other complicated equipment.
fig.14-23e
* To conduct binary playback, you will need to obtain a control
device capable of generating binary signals.
* Input of binary specifications should be completed in no more
than 50 milliseconds.
Program 1
1
A0001
2
A0002
No. Phrase
3
A0003
:
:
100 A0100
Program 2–5: No setting has been supplied.
START signal
Binary Specification Port 1–11
000001110000
Phrase A0112
Playback
AR-3000R_e.book 92 ページ ２０１０年３月１８日 木曜日 午後２時６分