Wayne-Dalton 9100 用户手册
7
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the
Find a Dealer section online at www.wayne-dalton.com
installation
begin the installation of the door by checking the opening. It must be the same size as the door. Vertical jambs must be plumb and the
header level. Side clearance, from edge of door to wall, must be minimum of 3-1/2” (89 mm) on each side.
header level. Side clearance, from edge of door to wall, must be minimum of 3-1/2” (89 mm) on each side.
imPoRTaNT: STAINLESS STEEL OR PT 2000 COATED LAG SCREWS MUST bE USED WHEN INSTALLING CENTER bEARING bRACkETS,
END bRACkETS, jAMb bRACkETS, OPERATOR MOUNTING/SUPPORT bRACkETS AND DISCONNECT bRACkETS ON TREATED LUMbER
(PRESERVATIVE-TREATED). STAINLESS STEEL LAG SCREWS ARE NOT NECESSARY WHEN INSTALLING PRODUCTS ON UNTREATED
LUMbER.
NoTe: It is recommended that 5/16” x 2” lag screws will be pilot drilled using a 3/16” drill bit, prior to fastening.
END bRACkETS, jAMb bRACkETS, OPERATOR MOUNTING/SUPPORT bRACkETS AND DISCONNECT bRACkETS ON TREATED LUMbER
(PRESERVATIVE-TREATED). STAINLESS STEEL LAG SCREWS ARE NOT NECESSARY WHEN INSTALLING PRODUCTS ON UNTREATED
LUMbER.
NoTe: It is recommended that 5/16” x 2” lag screws will be pilot drilled using a 3/16” drill bit, prior to fastening.
NoTe: If you have riveted track, skip steps, 1 through 2 and proceed to step3.
iNST
alla
Tio
N
1
cutting vertical Track and
installing q.i. jamb brackets
3RD SET HOLES
2ND SET HOLES
TWISTLOCk TAb
LEfT SIDE SHOWN
RIGHT SIDE SHOWN
Tape Measure
Hacksaw
Power Drill
5/16” Drill bit
Vertical track must be cut to the proper
length prior to installation.
imPoRTaNT: DOORS THAT ARE 7’-0” OR
imPoRTaNT: DOORS THAT ARE 7’-0” OR
8’-0” IN HEIGHT DO NOT REqUIRE CUTTING
THE VERTICAL TRACk.
Determine the radius of your horizontal
Determine the radius of your horizontal
track.
NoTe: All Portland tracks have the radius
NoTe: All Portland tracks have the radius
stamped on the side of the track.
Using this measurement, refer to the vertical
Using this measurement, refer to the vertical
track cutting chart to determine the length
of the vertical track. Cut the track off at the
TOP.
Now, two holes must be drilled into the
Now, two holes must be drilled into the
top of the cut vertical track. Refer to the
illustration shown for hole locations. Use a
5/16” drill bit.
Repeat for other vertical track.
Measure the length of the vertical tracks.
Repeat for other vertical track.
Measure the length of the vertical tracks.
Using the jamb bracket schedule, determine
the placement of the jamb brackets for your
door height.
To install the jamb brackets, align the
To install the jamb brackets, align the
twistlock tab on the quick install jamb
bracket with the quick install feature in the
track and turn the bracket perpendicular to
the track so the mounting flange is toward
the back (flat) leg of the track.
1
12”
12”
Horizontal
track
track
Stamped
radius
radius
qI jAMb bRACkET
TOP
HOLE
bOTTOM
HOLE
MIDDLE
HOLE
qUICk INSTALL fEATURE
1ST SET HOLES
Tools Needed: