Enviro EG 28 B 用户手册
MAINTENANCE AND TECHNICAL
Annually check to ensure that your
Venting system is clear.
Venting system is clear.
Periodically check the pilot and burner. Check to
see that all the burner ports are clean and clear.
Check the pilot head for blockage. Check to ensure
the pilot flame is blue with small yellow tips.
see that all the burner ports are clean and clear.
Check the pilot head for blockage. Check to ensure
the pilot flame is blue with small yellow tips.
CLEANING OF GLASS
Do not clean glass when hot
It will be necessary to clean the ceramic glass
periodically. During a cold start up, condensation
will sometimes form on the glass, this is a normal
condition with all gas fireplaces and stoves.
However, this condensation can allow dust and lint
to cling to the glass surface. Initial paint curing of the
appliance can leave behind a slight film on the glass.
This is a temporary problem. It is therefore
recommended that the glass be cleaned initially after
about the first two weeks of use.
It will be necessary to clean the ceramic glass
periodically. During a cold start up, condensation
will sometimes form on the glass, this is a normal
condition with all gas fireplaces and stoves.
However, this condensation can allow dust and lint
to cling to the glass surface. Initial paint curing of the
appliance can leave behind a slight film on the glass.
This is a temporary problem. It is therefore
recommended that the glass be cleaned initially after
about the first two weeks of use.
After that, depending upon the amount of use,
cleaning should be required no more than two or
three times per season.
cleaning should be required no more than two or
three times per season.
To clean the door, use a mild glass cleaner and a
soft cloth. Abrasive cleaners will damage the glass
and gold surfaces.
soft cloth. Abrasive cleaners will damage the glass
and gold surfaces.
OPENING THE DOOR
Turn unit off and wait until the appliance has cooled
down.
1. Open the right hand hinged side flap, which will
expose a door fastener. Using a 1/2" wrench,
loosen the fastener.
down.
1. Open the right hand hinged side flap, which will
expose a door fastener. Using a 1/2" wrench,
loosen the fastener.
3. Due to the shape of the bay window door. You
must also open the left-hand side flap before
attempting to open the door.
attempting to open the door.
3. Ensure the door is properly fastened after
cleaning before attempting to re-light the appliance
cleaning before attempting to re-light the appliance
.
TO REPLACE DOOR AND GLASS ASSEMBLY
The glass in this appliance is an integral part of the
door assembly. If the glass is damaged or broken a
replacement door assembly including glass must be
fitted.
door assembly. If the glass is damaged or broken a
replacement door assembly including glass must be
fitted.
To Replace:
• open door fully
• Lift door vertically so that hinge pins lift out of
• open door fully
• Lift door vertically so that hinge pins lift out of
hinge receivers.
• Return the door assembly to dealer.
Door and glass assembly must be replaced as a
complete unit by your ENVIROGAS Dealer.
No substitute materials are allowed.
Door and glass assembly must be replaced as a
complete unit by your ENVIROGAS Dealer.
No substitute materials are allowed.
Use extreme caution cleaning up broken glass. Use
thick gloves and broom to brush glass up.
FOR CLEANING THE INSIDE OF THE FIREBOX
Remove the log carefully from the firebox. Gently
remove the embers and place on a piece of paper
towel. Until ready to replace.
Remove the log carefully from the firebox. Gently
remove the embers and place on a piece of paper
towel. Until ready to replace.
Vacuum the firebox thoroughly. Carefully clean off
any dust on the logs and remove any lint from the
main burner and pilot burner.
any dust on the logs and remove any lint from the
main burner and pilot burner.
After carefully replacing the log and embers in their
correct positions, and the door has been resealed,
re-light the pilot, following the instructions on the
attached label.
correct positions, and the door has been resealed,
re-light the pilot, following the instructions on the
attached label.
CLEARANCES MUST BE SUFFICIENT TO ALLOW
ACCESS FOR MAINTENANCE AND SERVICE
ACCESS FOR MAINTENANCE AND SERVICE
TROUBLE SHOOTING
10