Panasonic RQT9223 用户手册

RQT9223

Dim the display for better viewing in a darkened room.

1.  To enter the SETUP (➔ page 36)
2.  Press [e][r] to select “DIMMER ”, and 

3.  Press [e][r] to select the setting, and 

Adjustment range: 

DIMMER 1 (bright) to DIMMER 3 (dim)

Factory setting: 

4. To finish the setting (➔ page 36)

•  Select “

DIMMER OFF ” to cancel.

•  The brightness changes at the point of changing the setting. 

To confirm the setting, press [OK].

The unit automatically turns off when set time passes. This is a 
convenient function when going to bed, etc.

1.  To enter the SETUP (➔ page 36)
2.  Press [e][r] to select “SLEEP ” and 

3.  Press [e][r] to select the setting, and 

Setting range: 

OFF, 30, 60, 90, 120 (minutes)

Factory setting : 

4.  To finish the setting (➔ page 36)

• To cancel, select “

OFF ”.

• “

SLEEP” is displayed when the setting is complete.

• Once the sleep timer is set, the remaining time is displayed in 

step 

2.

• To change the setting, set time again in step 

3.

You can set connected speakers and their sizes manually.
Different ranges are played by different speakers. Size setting 
is necessary for reproducing sources, particularly their bass 
section, completely.

1.  To enter the SETUP (➔ page 36)
2.  Press [e][r] to select “SPK SIZE ”, and 

3.  Press [e][r] to select a speaker to set, 

SUBW : Subwoofer, LR : Front speakers, 
C : Center speaker, S : Surround speakers, 
SB : Surround back speakers

4.  Press [e][r] to change the setting, and 

SUBW : NO ; unconnected    YES ; connected
LR, C, S : 
NONE ;  For speakers you haven’t connected (center or 

surround only). 

SMALL ; For speakers that cannot adequately reproduce 

the bass range. This setting is sufficient for most 
speakers if you are using a subwoofer.

LARGE ; For speakers that can sufficiently reproduce the 

bass range down to 20 Hz.

SB :
NONE ; For speakers you haven’t connected.
1-SPK ; If you connect one surround back speaker.
2-SPK ; If you connect two surround back speakers.

Factory settings:

  SUBW ;  YES

 

LR, C, S ;  SMALL

SB ; 

5. To finish the setting (➔ page 36)

• Set the lowpass filter frequency according to frequencies 

available for playback when speakers are set as “

SMALL ”. 

The factory setting is 80 Hz (➔ page 38).

• See the note on page 51.

By adjusting the distance from each speaker (except the 
subwoofer) to the seating area, the sound delay time is 
automatically adjusted so that sound reaches the listener at 
the same time.

1.  To enter the SETUP (➔ page 36)
2.  Press [e][r] to select “DISTANCE ”, and 

3.  Press [e][r] to select a speaker to set, 

L : Front left, R :  Front right,  C :  Center,  
LS :  Surround left, RS : Surround right,  
SBL : Surround back left, 
SBR :  Surround back right

4.  Press [e][r] to select the distance and 

Adjustment range: 

1.0  to 45.0 ft (feet)

This unit is adjusted at 0.5 feet intervals.
Factory settings: 

L, R ; 

10.0 ft (feet)

C ; 

10.0 ft (feet)

LS, RS ; 

5.0 ft (feet)

SBL, SBR ;  5.0 ft (feet)

5. To finish the setting (➔ page 36)

• Speakers whose polarity was automatically adjusted through 

the auto speaker setup (➔ pages 24 and 25) are displayed 
with “

– ” such as “L 3.0 – ”.

• When the speaker distance measured through the auto 

speaker setup (➔ pages 24 and 25) exceeds 15 meters 
(45 feet), the distance is displayed as “

OVER ”.

SA-BX500-PP (RQT9223-Y)_En.indd   37

6/27/2008   4:06:16 PM