Panasonic RQT9223 用户手册
38
RQT9223
Using the setup menu
Setting the lowpass filter
If the speaker sizes (➔ page 37) are set to “
SMALL ”, make
this setting.
The unit cannot reproduce the entire bass range when
speakers are set as “
The unit cannot reproduce the entire bass range when
speakers are set as “
SMALL ”. You can arrange the unit to
provide missing bass sounds through the subwoofer by setting
the lowpass filter frequency according to frequencies available
for playback.
the lowpass filter frequency according to frequencies available
for playback.
1. To enter the SETUP (➔ page 36)
2. Press [e][r] to select “FILTER FRQ ”,
2. Press [e][r] to select “FILTER FRQ ”,
and press [OK] to confirm.
3. Press [e][r] to select the lowpass filter
frequency, and press [OK] to confirm.
Lowpass filter frequency for sending the bass range to the
subwoofer:
subwoofer:
40, 60, 80, 100, 120, 150, 200 (Hz)
Factory setting:
80 (Hz)
4. To finish the setting (➔ page 36)
Note
• The setting made through these steps applies to all speakers
set as “
SMALL ”.
Changing auto speaker settings
To return speakers to factory settings
You can return settings made with the setup microphone to
factory settings. (The “AUTO SPEAKER SETUP” indicator goes
off when you perform this operation.)
factory settings. (The “AUTO SPEAKER SETUP” indicator goes
off when you perform this operation.)
1. To enter the SETUP (➔ page 36)
2. Press [e][r] to select “AUTO SETUP ”,
2. Press [e][r] to select “AUTO SETUP ”,
and press [OK] to confirm.
3. Press [e][r] to select “DEFAULT ”, and
press [OK] to confirm.
4. Press [e][r] to select “YES ”, and press
[OK] to confirm.
YES : For returning to factory settings
NO : For keeping auto settings
Factory setting:
NO : For keeping auto settings
Factory setting:
NO
• To cancel, select “
NO ”.
5. To finish the setting (➔ page 36)
Setting the unit against automatic polarity
adjustment
adjustment
The unit judges polarity of certain properly connected speakers
as opposite. When this happens, set the unit against automatic
polarity adjustment and prevent polarity reversal.
as opposite. When this happens, set the unit against automatic
polarity adjustment and prevent polarity reversal.
1. To enter the SETUP (➔ page 36)
2. Press [e][r] to select “AUTO SETUP ”,
2. Press [e][r] to select “AUTO SETUP ”,
and press [OK] to confirm.
3. Press [e][r] to select “POLARITY ”, and
press [OK] to confirm.
4. Press [e][r] to select “CHECK NO ”, and
press [OK] to confirm.
CHECK YES : Normal auto speaker setup
CHECK NO : No automatic polarity adjustment
Factory setting:
CHECK NO : No automatic polarity adjustment
Factory setting:
CHECK YES
5. To finish the setting (➔ page 36)
Adjusting the high-frequency sound quality of
the set frequency response
the set frequency response
You can adjust the high-frequency sound quality set for your
preference.
preference.
1. To enter the SETUP (➔ page 36)
2. Press [e][r] to select “AUTO SETUP ”,
2. Press [e][r] to select “AUTO SETUP ”,
and press [OK] to confirm.
3. Press [e][r] to select “EQ ADJUST ”,
and press [OK] to confirm.
4. Press [e][r] to select the setting, and
press [OK] to confirm.
OFF : For not using a set frequency response.
SOFT : High-frequency adjustment is rather small.
NORMAL : High-frequency adjustment is medium.
HARD : High-frequency adjustment is rather big.
Factory setting:
SOFT : High-frequency adjustment is rather small.
NORMAL : High-frequency adjustment is medium.
HARD : High-frequency adjustment is rather big.
Factory setting:
NORMAL
5. To finish the setting (➔ page 36)
Making bi-wire setting
Make sure to select “
YES ” when you connect the unit to bi-
wire speakers. The speakers do not produce adequate sounds
unless you make this setting.
unless you make this setting.
1. To enter the SETUP (➔ page 36)
2. Press [e][r] to select “LR BI-WIRE ”, and
2. Press [e][r] to select “LR BI-WIRE ”, and
press [OK] to confirm.
3. Press [e][r] to select “YES ”, and press
[OK] to confirm.
YES : When bi-wire speakers are connected
NO : When bi-wire speakers are not connected
Factory setting:
NO : When bi-wire speakers are not connected
Factory setting:
NO
4. To finish the setting (➔ page 36)
Setting the speaker impedance
Make this setting when the speaker impedance is low (4
Ω).
1. To enter the SETUP (➔ page 36)
2. Press [e][r] to select “SPKR IMP ”, and
2. Press [e][r] to select “SPKR IMP ”, and
press [OK] to confirm.
3. Press [e][r] to select “4 OHMS ”, and
press [OK] to confirm.
6 OHMS : When the speaker impedance is normal
4 OHMS : When the speaker impedance is low (4
4 OHMS : When the speaker impedance is low (4
Ω)
Factory setting:
6 OHMS
4. To finish the setting (➔ page 36)
Note
• If at least one speaker among connected speakers has the
impedance of 4
Ω, set “4 OHMS ”.
SA-BX500-PP (RQT9223-Y)_En.indd 38
6/27/2008 4:06:17 PM