ONKYO TX-SR876 用户手册
61
If the impedance of any speaker is 4 ohms or more but
less than 6, set the Speaker Impedance to 4 ohms.
less than 6, set the Speaker Impedance to 4 ohms.
To use bi-amping or bridging, you must change the
“Speaker Type” setting. For hookup information, see
pages 27–30.
“Speaker Type” setting. For hookup information, see
pages 27–30.
Notes:
• When bridging is used, the AV receiver is able to drive
• When bridging is used, the AV receiver is able to drive
up to 5.1 speakers in the main room.
• When bi-amping is used, the AV receiver is able to
drive up to 5.1 speakers in the main room.
• Before you change these settings, turn down the vol-
ume.
Speaker Settings
The onscreen menus shown in this manual may be
slightly different from what you see on your TV.
slightly different from what you see on your TV.
1
Press the [RECEIVER] button,
followed by the [SETUP] button.
The main menu appears onscreen.
followed by the [SETUP] button.
The main menu appears onscreen.
If the main menu doesn’t appear, make
sure the appropriate external input is
selected on your TV.
sure the appropriate external input is
selected on your TV.
2
Use the Up and Down [
q]/[w] but-
tons to select “2. Speaker
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
Setup”, and then press [ENTER].
The “Speaker Setup” menu appears.
INPUT SELECTOR
DISPLAY
MUTING
GU
IDE
EXI
T
PREV
CH
DIMMER
CDR/MD/DOCK
SAT
TAPE/AMP
SLEEP
MACRO
REMOTE MODE
--/--- 10
11
12
PLAYLIST
RANDOM
D. TUN
CD
TUNER
TAPE
PHONO
REC
ENTER
TO
P M
ENU
MEN
U
VOL
CH
DISC
ALBUM
TV
VCR
CABLE
NET/USB
DVD
RECEIVER
CD
-
1
2
3
ZONE
3
ZONE
2
+
-
+10
0
CLEAR
4
5
6
7
8
9
SE
TUP
RET
UR
N
NET/USB
2, 3
1
1, 7
2–6
If you change these settings, you must run the auto-
matic speaker setup again (see page 64).
matic speaker setup again (see page 64).
2. Speaker
Setup
1. Speaker
Settings
2. Speaker
Config
3. Speaker
Distance
4. Level
Calibration
5. Equalizer
Settings
6. THX Audio Setup
3
Use the Up and Down [
q]/[w] but-
tons to select “1. Speaker Set-
tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
tings”, and then press [ENTER].
The “Speaker Settings” menu appears.
4
Use the Up and Down [
q]/[w] but-
tons to select “Speaker imped-
ance”, and use the Left and Right
[
ance”, and use the Left and Right
[
e]/[r] buttons to select:
4ohms: Select if the impedance of any
speaker is 4 ohms or more but
less than 6.
less than 6.
6ohms: Select if the impedances of all
speakers are between 6 and
16 ohms.
16 ohms.
5
Use the Up and Down [
q]/[w] but-
tons to select “Front(Speaker
A)”, and use the Left and Right
[
A)”, and use the Left and Right
[
e]/[r] buttons to select:
Normal:
Select this if you’ve connected your
front Speakers A normally.
front Speakers A normally.
Bi-Amp:
Select this if you’ve connected your
front Speakers A for bi-amped
operation.
front Speakers A for bi-amped
operation.
BTL:
Select this if you’ve connected your
front Speakers A for bridged opera-
tion. The BTL indicator will appear
on the display.
front Speakers A for bridged opera-
tion. The BTL indicator will appear
on the display.
Note:
“Bi-Amp” and “BTL” cannot be
selected if “Front(Speaker B)” is set to
“Bi-Amp” or “BTL”.
“Bi-Amp” and “BTL” cannot be
selected if “Front(Speaker B)” is set to
“Bi-Amp” or “BTL”.
2–1. Speaker
Settings
Speaker impedance
Speaker Type
Front(Speaker
Speaker Type
Front(Speaker
A)
Front(Speaker
B)
6ohms
Normal
Not Use
MOVE
VALUE
RETURN
RETURN
EXIT
SETUP