ONKYO TX-NR5009 用户手册
70
En
Dolby Volume
■
Dolby Volume
Note
• This setting cannot be used in either of the following cases:
– Pure Audio or Direct listening mode is selected.
– the multichannel analog input is selected.
– Speakers B is being used.
– any of the THX listening modes is selected, with “Loudness
– the multichannel analog input is selected.
– Speakers B is being used.
– any of the THX listening modes is selected, with “Loudness
Plus” set to “On” or “Preserve THX Settings” set to “Yes”
(
(
).
• When “Dolby Volume” is set to “On”, the “Dynamic EQ” and
“Dynamic Volume” settings of all input selectors are switched
to “Off”.
to “Off”.
• When “Sound Program” is enabled, the setting must be made
with the “Sound Program Edit”.
Audyssey
■
Audyssey
).
■
Dynamic EQ
■
Dynamic Volume
).
Note
• These technologies can be used when all the following
conditions are met:
– Room Correction and Speaker Setup is completed. Note that
– Room Correction and Speaker Setup is completed. Note that
“Audyssey” requires the “Audyssey MultEQ XT32 Full
Calibration” method.
Calibration” method.
– Any listening mode other than Direct or Pure Audio is
selected.
– A pair of headphones is not connected.
– multichannel analog input is not selected.
– Speakers B is not being used.
– multichannel analog input is not selected.
– Speakers B is not being used.
• The setting is stored individually for each input selector.
• “Dynamic EQ” and “Dynamic Volume” cannot be selected
• “Dynamic EQ” and “Dynamic Volume” cannot be selected
when any of the THX listening modes is selected, with
“Loudness Plus” set to “On” or “Preserve THX Settings” set
to “Yes” (
“Loudness Plus” set to “On” or “Preserve THX Settings” set
to “Yes” (
).
• When “Dynamic EQ” is set to “On” or “Dynamic Volume” is
set to anything else than “Off”, “Dolby Volume” will be
switched to “Off”.
switched to “Off”.
• When “Sound Program” is enabled, the setting must be made
with the “Sound Program Edit”.
Late Night
■
Late Night
For Dolby Digital and Dolby Digital Plus sources, the
options are:
options are:
`
Off
`
Low:
Small reduction in dynamic range.
`
High:
Large reduction in dynamic range.
For Dolby TrueHD sources, the options are:
`
Auto:
The Late Night function is set to “On” or “Off”
automatically.
automatically.
`
Off
`
On
Turn this setting on to reduce the dynamic range of Dolby
Digital material so that you can still hear quiet parts even
when listening at low volume levels—ideal for watching
movies late at night when you don’t want to disturb
anyone.
Digital material so that you can still hear quiet parts even
when listening at low volume levels—ideal for watching
movies late at night when you don’t want to disturb
anyone.
Note
• The effect of the Late Night function depends on the material
that you are playing and the intention of the original sound
designer, and with some material there will be little or no effect
when you select the different options.
designer, and with some material there will be little or no effect
when you select the different options.
• The Late Night function can be used only when the input source
is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.
• The Late Night function is set to “Off” when the AV receiver is
set to standby. For Dolby TrueHD sources, it will be set to
“Auto”.
“Auto”.
Music Optimizer
■
Music Optimizer
`
Off
`
On
Turn this setting on to enhance the sound quality of
compressed music files. Use it with music files that use
“lossy” compression, such as MP3.
compressed music files. Use it with music files that use
“lossy” compression, such as MP3.
Note
• The Music Optimizer function only works with PCM digital
audio input signals with a sampling rate below 48 kHz and
analog audio input signals.
analog audio input signals.
• The Music Optimizer is disabled when the Direct or Pure Audio
listening mode is selected.
• The setting is stored individually for each input selector.
• The M.Opt indicator will light (
• The M.Opt indicator will light (
).
• This setting is not available when the multichannel analog input
is selected.
• When “Sound Program” is enabled, the setting must be made
with the “Sound Program Edit”.