JVC GET0570-001A 用户手册

1

0808DTSMDTJEIN

EN

GET0572-002A

[UI]

© 2008 Victor Company of Japan, Limited

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does 
not have this system, a voltage inverter is required, which can be purchased at JVC car audio dealers.

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all 
electrical connections before installing the unit.
•  Be sure to ground this unit to the car’s chassis again after installation.

Notes:
•  Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car 

audio dealer.

•  It is recommended to connect speakers with a maximum power of more than 50 W (both at the 

rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, 
change “AMP GAIN” setting to prevent the speakers from being damaged (see page 22 of the 
INSTRUCTIONS).

•  To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.
•  The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

•  DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit 

•  BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring 

in your car.

J
Handles

G
Lock nut (M5)

I
Rubber 
cushion

A / B
Hard case/Control 
panel

C
Sleeve

E
Power cord

L
Battery

K
Remote controller

Heat sink

H
Mounting bolt (M4 × 5 mm; 
M5 × 12.5 mm)

F
Washer (ø5)

The following parts are provided for this unit. If any item is missing, consult your JVC car audio 
dealer immediately.

D
Trim plate

*

1 

When you stand the unit, be careful not to damage the fuse on the rear.

*

2

  Not supplied for this unit.

Insert the two handles, then pull them as illustrated 
so that the unit can be removed.

In a Toyota car for example, first remove the 
car radio and install the unit in its place.

  When installing the unit on the 

mounting bracket, make sure to 
use the 8 mm-long screws. If longer 
screws are used, they could damage 
the unit.

Bracket

*

2

Flat head screws (M5 × 8 mm) 

*

2

Bracket 

*

2

The following illustration shows a typical installation. If you have any questions or require information 
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
•  If you are not sure how to install this unit correctly, have it installed by a qualified technician.

Before removing the unit, release the rear section.

Do the required electrical connections.

Bend the appropriate tabs to 
hold the sleeve firmly in place.

Pocket

Flat head screws 
(M5 × 8 mm) 

*

2

•  The fuse blows.
*  Are the red and black leads connected correctly?

•  Power cannot be turned on.
*  Is the yellow lead connected?

•  No sound from the speakers.
*  Is the speaker output lead short-circuited?

•  Sound is distorted.
*  Is the speaker output lead grounded?
*  Are the “–” terminals of L and R speakers grounded in common?

•  Noise interfere with sounds.
*  Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

•  This unit becomes hot.
*  Is the speaker output lead grounded?
*  Are the “–” terminals of L and R speakers grounded in common?

•  This unit does not work at all.
*  Have you reset your unit?

Screw (option)

Stay (option)

Fire wall

Dashboard

Install the unit at an 
angle of less than 30˚.

Install1-2_KD-R404[UI]_1.indd   1

Install1-2_KD-R404[UI]_1.indd   1

8/9/08   12:24:37 PM

8/9/08   12:24:37 PM