Tandberg Data 1080P 用户手册
D14640.01—MARCH 2010
24
TANDBERG PrecisionHD 1080p/720p camera
Camera User Guide
Contents
Introduction
Physical interface
Cables
Connecti to codec
Video formats
Daisy chaining
Appendices
Contact us
www.tandberg.com
Command
Command Packet
Comments
PT_Direct
8x 01 06 02 0p 0t 0q 0r 0s
0u 0v 0w 0x 0y FF
0u 0v 0w 0x 0y FF
p: max pan speed
t: max tilt speed
qrsu: pan position
vwxy: tilt position
Attempts to linearize movement.
t: max tilt speed
qrsu: pan position
vwxy: tilt position
Attempts to linearize movement.
PTZF_Direct
8x 01 06 20 0p 0q 0r 0s 0t
0u 0v 0w 0x 0y 0z 0g 0h
0i 0j 0k ff
0u 0v 0w 0x 0y 0z 0g 0h
0i 0j 0k ff
NOTE: Never route this message
through Sony cameras.
Sets all motors in one operation.
pqrs: pan
tuvw: tilt
xyzg: zoom
hijk: focus
Attempts to linearize movement for pan
and tilt.
through Sony cameras.
Sets all motors in one operation.
pqrs: pan
tuvw: tilt
xyzg: zoom
hijk: focus
Attempts to linearize movement for pan
and tilt.
PT_Limit_Set
8x 01 06 07 00 0x 0p 0q
0r 0s 0t 0u 0v 0w ff
0r 0s 0t 0u 0v 0w ff
x=1: Up/Right
x=0: Down/Left
pqrs: Pan limit
tuvx: Tilt limit.
This command is valid only to next
boot.
x=0: Down/Left
pqrs: Pan limit
tuvx: Tilt limit.
This command is valid only to next
boot.
PT_Limit_Clear
8x 01 06 07 01 0x [...] ff
x=1: Up/Right
x=0: Down/Left
Sony specifies lots of filler bytes after
0x. Ignore them.
x=0: Down/Left
Sony specifies lots of filler bytes after
0x. Ignore them.
Command
Command Packet
Comments
Zoom_Stop
8x 01 04 07 00 ff
Zoom_Tele
8x 01 04 07 2p ff
p = speed parameter,
a (low) to b (high)
a (low) to b (high)
Zoom_Wide
8x 01 04 07 3p ff
Zoom_Direct
8x 01 04 47 0p 0q 0r 0s ff
pqrs: zoom position
ZoomFocus_Direct
8x 01 04 47 0p 0q 0r
0s
0t 0u 0v 0w ff
0s
0t 0u 0v 0w ff
pqrs: zoom position
tuvw: focus position
tuvw: focus position
Focus_Stop
8x 01 04 08 00 ff
Focus_Far
8x 01 04 08 2p ff
p = speed parameter,
a (low) to b (high)
a (low) to b (high)
Focus_Near
8x 01 04 08 3p ff
Focus_Direct
8x 01 04 48 0p 0q 0r 0s ff
pqrs: focus position
Focus_Auto
8x 01 04 38 02 ff
Autofocus mode on/off.
NOTE:
If mode is auto, camera may
disable autofocus when focus is ok.
Autofocus will be turned back on when
camera is moved using Zoom_Tele/
Wide, PT_Up/Down/Left/Right. Ditto
for IR_CameraControl movement.
Autofocus will be turned back on when
camera is moved using Zoom_Tele/
Wide, PT_Up/Down/Left/Right. Ditto
for IR_CameraControl movement.
Focus_Manual
8x 01 04 38 03 ff
PT_Stop
8x 01 06 01 03 03 03 03 ff
PT_Reset
8x 01 06 05 ff
Reset pan/tilt to center position. Will
also re–synchronize motors.
also re–synchronize motors.
PT_Up
8x 01 06 01 0p 0t 03 01 ff
p pan speed
t: tilt speed
Right -> increment pan
Left -> decrement pan
Up -> increment tilt
Down -> decrement tilt
t: tilt speed
Right -> increment pan
Left -> decrement pan
Up -> increment tilt
Down -> decrement tilt
PT_Down
8x 01 06 01 0p 0t 03 02 ff
PT_Left
8x 01 06 01 0p 0t 01 03 ff
PT_Right
8x 01 06 01 0p 0t 02 03 ff
PT_UpLeft
8x 01 06 01 0p 0t 01 01 ff
PT_UpRight
8x 01 06 01 0p 0t 02 01 ff
PT_DownLeft
8x 01 06 01 0p 0t 01 02 ff
PT_DownRight
8x 01 06 01 0p 0t 02 02 ff
The VISCA™/RS–232 control protocol, cont...
PTZF - movement commands
Contact us
Contents
Introduction
Cables
Daisy chaining
Appendices
Physical interface
Connect to codec
Video formats
Appendices