Husqvarna CTH2542 TWIN 用户手册

FIG. 2

02591

DISCARD

TERMINAL

PROTECTIVE

CAPS

BATTERY

COVER

KEPS

NUT

HEX BOLT

POSITIVE CABLE

(RED)

NEGATIVE

CABLE

(BLACK)

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.
• Remove adjustment knob and flat washer securing

seat to cardboard packing and set aside for assembly

of seat to tractor.

•

Pivot seat upward and remove from the cardboard pack-

ing. Remove the cardboard packing and discard.

• Place seat on seat pan so head of shoulder bolt is

positioned over large slotted hole in pan.

• Push down on seat to engage shoulder bolt in slot and

pull seat towards rear of tractor.

• Pivot seat and pan forward and assemble adjustment

knob and flat washer loosely. Do not tighten.

• Lower seat into operating position and sit on seat.
• Slide seat until a comfortable position is reached

which allows you to press clutch/brake pedal all the

way down.

• Get off seat without moving its ad just ed position.
• Raise seat and tighten adjustment knob securely.

FIG. 3

024

02464

SEAT PAN

SHOUL DER BOLT

AD JUST MENT KNOB

FLAT

WASH ER

SEAT

FIG. 4A

TO INSTALL BAGGER COM PO NENTS TO

TRAC TOR (See Figs. 4A-4D)

•

Remove discharge chute from rear of tractor. Unhook

the two (2) straps and pull chute out and away from

tractor.

•

Remove the two (2) 3/8 nuts and flat washers from the

bolts at the tractor back plate.

277

DISCHARGE

CHUTE

3/8 NUT

FLATWASHER

NOTE: You may now roll or drive your tractor off the skid.

Follow the ap pro pri ate instruction below to remove the

tractor from the skid.

WARNING: Before start ing, read, un der stand and fol low

all in struc tions in the Op er a tion section of this man u al. Be

sure tractor is in a well-ventilated area. Be sure the area in

front of tractor is clear of other peo ple and objects.

TO ROLL TRACTOR OFF SKID (See Op-

er a tion section for location and function of

con trols)

• Press lift lever plunger and raise attachment lift lever

to its highest po si tion.

• Release parking brake by de press ing clutch/brake

ped al.

• Place freewheel control in "trans mis sion dis en gaged

position" (See “TO TRANS PORT” in the Op er a tion

section of this manual).

• Roll tractor forward off skid.
•

Remove banding holding the deflector shield up against

tractor.

TO DRIVE TRAC TOR OFF SKID (See Op-

er a tion section for location and function of

con trols)

WARNING: Before start ing, read, un der stand and fol low

all in struc tions in the Op er a tion section of this man u al. Be

sure tractor is in a well-ventilated area. Be sure the area in

front of tractor is clear of other peo ple and objects.
•

Be sure all the above assembly steps have been com-

pleted.

• Check engine oil level and fill fuel tank with gasoline.
• Place freewheel control in "trans mis sion en gaged"

po si tion (see "TO TRANSPORT" in Op er a tion section

of this manual).

•

Sit on seat in operating position, depress clutch/brake

pedal and set the parking brake.

• Place motion control lever in neutral (N) position.
• Press lift lever plunger and raise attachment lift lever

to its highest position.

• Remove key from bag and start the engine (see "TO

START ENGINE" in the Operation section of this man-

ual). After engine has started, move throttle control to

idle (slow) position.

• Release parking brake.
•

Slowly move the mo tion control lever for ward and slowly

drive tractor off skid.

•

Apply brake to stop trac tor, set park ing brake and place

motion con trol lever in neutral po si tion.

• Turn ignition key to "STOP" position.
Continue with the in struc tions that follow.