Husqvarna P 520D 用户手册
36 –
English
Lubrication
The following oil classes are recommended:
•
API Service Class: CH4 or ACEA E5 or higher.
Choose an oil with viscosity according to the temperature
ranges in the figure:
ranges in the figure:
Do not mix different types of oil.
Replacing the engine oil
Open the engine cover.
The engine oil should be changed the first time after 25 hours
running time. It should then be changed after every 100 hours
of running time.
running time. It should then be changed after every 100 hours
of running time.
1
Place a container underneath the engine oil drain plug.
2
Remove the dipstick. Remove the drain plug from the
engine.
engine.
3
Let the oil run out into the container.
4
Fit the drain plug and tighten it.
5
Change oil filter if necessary.
6
If necessary fill so that the oil comes up to the FULL mark
on the dipstick.
on the dipstick.
7
Run the engine warm, then check that there is no leakage
from the oil plug.
from the oil plug.
8
Check the engine oil level and top up if necessary.
Changing the oil filter
The oil filter is located on the right side of the engine.
•
Open the engine cover.
•
Place a suitable vessel to collect the oil in.
•
Turn the old oil filter anti-clockwise to remove. If
necessary, use a filter remover.
necessary, use a filter remover.
•
Clean the oil filter bracket.
•
Lightly lubricate the rubber seal on the new oil filter using
new oil.
new oil.
•
Fit the oil filter by turning clockwise. Turn by hand until the
rubber seal is seated. Now tighten a further half turn.
rubber seal is seated. Now tighten a further half turn.
•
Start the engine and let it idle for about 3 minutes. Now
stop it and check for signs of leakage.
stop it and check for signs of leakage.
•
Check the engine oil level and top up if necessary.
Check the hydraulic system oil level
The oil and filter should be changed by an authorised service
representative, as described in the Workshop Manual. Work
on the system entails particular demands on cleanliness and
the system must be vented before the machine is used.
representative, as described in the Workshop Manual. Work
on the system entails particular demands on cleanliness and
the system must be vented before the machine is used.
•
Fold up the seat.
•
Remove the filler cap. The level should be 40-60 mm from
the strainer top.
the strainer top.
•
Refill as required with fully synthetic 10W/50 API SM oil or
better
better
!
WARNING! Engine oil can be very hot if it is
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
IMPORTANT INFORMATION
Used engine oil, antifreeze etc. is a health hazard and must
not be disposed of on the ground or in nature; it should
always be disposed of at a workshop or appropriate
disposal location.
not be disposed of on the ground or in nature; it should
always be disposed of at a workshop or appropriate
disposal location.
Avoid skin contact; wash with soap and water in case of
spills.
spills.
-30 -20 -10 0 10 20 30 40 50 C
-22 -4 -14 32 50 68 86 104 122 F
0W
5W 20
10W 30
20
30
40
15W 40
20W 50
!
WARNING! Engine oil can be very hot if it is
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
IMPORTANT!
Used engine oil and transmission oil is hazardous to health
and must not be disposed of in the ground or out of doors.
and must not be disposed of in the ground or out of doors.
Replaced filters must be handed in to the workshop or other
allotted place for disposal.
allotted place for disposal.
Avoid skin contact; wash with soap and water in case of
spills.
spills.