Husqvarna 16 AWD 用户手册
English
– 31
Lubrication
Checking the engine’s oil level.
Check the oil level in the engine when the Rider stands
horizontal with the engine switched off.
horizontal with the engine switched off.
Open the engine cover.
Loosen the dipstick, pull it up and wipe it off.
The dipstick should be completely screwed down
Pull the dipstick out again and read the oil level.
The oil level should be between the markings on the dipstick.
If the level is approaching the ADD mark, top up the oil to the
FULL mark on the dipstick.
If the level is approaching the ADD mark, top up the oil to the
FULL mark on the dipstick.
The oil is topped up through the hole the dipstick sits in.
Fill the oil slowly. Tighten the dipstick correctly before starting
the engine. Start and run the engine at idling speed for
approx. 30 seconds. Turn off the engine. Wait 30 seconds and
check the oil level. If necessary fill so that the oil comes up to
the FULL mark on the dipstick.
the engine. Start and run the engine at idling speed for
approx. 30 seconds. Turn off the engine. Wait 30 seconds and
check the oil level. If necessary fill so that the oil comes up to
the FULL mark on the dipstick.
First and foremost use synthetic engine oil class SJ-CF 5W/
30 or 10W/30 for all temperature ranges. Mineral oil SAE30,
class SF–CC can be used at temperatures > +5
30 or 10W/30 for all temperature ranges. Mineral oil SAE30,
class SF–CC can be used at temperatures > +5
°C (40 °F)
Do not mix different types of oil.
Replacing the engine oil
The engine oil should be changed the first time after 5 hours
running time. It should then be changed after every 50 hours
of running time.
running time. It should then be changed after every 50 hours
of running time.
When operating with a heavy load or at high ambient
temperatures, replace every 25 hours.
temperatures, replace every 25 hours.
1
Place a container underneath the engine’s left oil drain
plug.
plug.
2
Remove the dipstick. Remove the drain plug from the
engine’s left side.
engine’s left side.
3
Let the oil run out into the container.
4
Fit the drain plug and tighten it.
5
Fill with oil up to the ”FULL” mark on the dipstick The oil is
topped up through the hole the dipstick sits in. See
Checking the engine’s oil level for filling instructions.
topped up through the hole the dipstick sits in. See
Checking the engine’s oil level for filling instructions.
The engine holds 1.5 litres (1.6 USqt) when the oil filter is
not replaced and 1.7 litres (1.8 USqt) of oil when the oil
filter is replaced.
not replaced and 1.7 litres (1.8 USqt) of oil when the oil
filter is replaced.
6
Run the engine warm, then check that there is no leakage
from the oil plug.
from the oil plug.
Checking the oil level in the
transmission on Rider 13 C, Rider 16
AWD and Rider 16 C
transmission on Rider 13 C, Rider 16
AWD and Rider 16 C
1
Remove the transmission cover. Undo the two screws
(one on each side) and lift off the transmission cover.
(one on each side) and lift off the transmission cover.
2
Rider 13 C and Rider 16 C Check that there is oil in the
transmission’s oil tank. Fill if necessary with engine oil
SAE 10W/30 (class SF–CC).
transmission’s oil tank. Fill if necessary with engine oil
SAE 10W/30 (class SF–CC).
!
WARNING! Engine oil can be very hot if it is
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
drained directly after stopping the engine.
Allow the engine to cool somewhat first.
ADD
FULL
ADD
FULL
IMPORTANT INFORMATION
Used engine oil is a health hazard and must not be
disposed of on the ground or in nature; it should always be
disposed of at a workshop or appropriate disposal location.
disposed of on the ground or in nature; it should always be
disposed of at a workshop or appropriate disposal location.
Avoid skin contact; wash with soap and water in case of
spills.
spills.