Roland XV-5080. 用户手册
215
Chapter 9 Other Settings/Status Checks
Chap.9
Selecting Common
Controllers ([SYSTEM/
UTILITY] - [F4 (Control)])
Controllers ([SYSTEM/
UTILITY] - [F4 (Control)])
These settings allow you to choose four MIDI controllers for
global use when controlling the parameters of any Patch or
Performance. The settings in each Patch or Performance will
determine whether the two controllers you choose here will
actually be used. In each Patch or Performance, you will also
need to specify the parameters to be controlled.
global use when controlling the parameters of any Patch or
Performance. The settings in each Patch or Performance will
determine whether the two controllers you choose here will
actually be used. In each Patch or Performance, you will also
need to specify the parameters to be controlled.
fig.09-006.e_70
System Control 1–4 (System Control
Source 1–4)
Source 1–4)
Available Settings:
OFF:
No controller is used.
CC01–95:
Controller numbers 1–95 (except for 32)
PITCH BEND:
Pitch Bend
AFTERTOUCH:
Aftertouch
Setting Procedure:
1. Press [SYSTEM/UTILITY], getting the indicator to light.
* If the indicator is blinking, you are in UTILITY mode. Press
[SYSTEM/UTILITY] once again to make its indicator light.
2. Press [F4 (Control)] to call up the SYSTEM Control page.
3. Press [
]/[
]/[
]/[
] to move the cursor to
the System Control (System Control Source) you wish to
set.
set.
4. Turn the VALUE dial or by press [INC]/[DEC], to select
the desired value.
* If you’ve made a mistake, simply press [UNDO]. The value of
the parameter will be restored to what it was when you first
positioned the cursor there.
positioned the cursor there.
5. Press [EXIT] to return to the applicable PLAY page.
Confirming the Current
Status ([SYSTEM/UTILITY] -
[F6 (Info)])
Status ([SYSTEM/UTILITY] -
[F6 (Info)])
fig.09-007.e_70
The basic steps needed to carry out the procedure are as
follows:
follows:
1. Press [SYSTEM/UTILITY], and confirm that its indicator
has lighted.
* If the indicator is blinking, you are in UTILITY mode. Press
[SYSTEM/UTILITY] once again to get the indicator to light
steadily.
steadily.
2. Press [F6 (Info)] to call up the SYSTEM Info page.
3. Press [EXIT] to return to the Play page.
Wave Expansion A–D (Wave
Expansion Board Name A–D)
Expansion Board Name A–D)
The display shows the names of Wave Expansion Boards
(SR-JV80 Series) installed in slots EXP A–D.
(SR-JV80 Series) installed in slots EXP A–D.
Slots without any boards installed are shown as “---------.”
SRX (SRX Board Name E–H)
The display shows the names of Wave Expansion Boards
(SRX Series) installed in slots EXP E–H.
(SRX Series) installed in slots EXP E–H.
Slots without any boards installed are shown as “---------.”
SIMM
This displays the installation status of any memory modules
(SIMMs), used for Wave data.
(SIMMs), used for Wave data.
BATTERY CHECK
The XV-5080 contains a battery that retains the data in its
internal memory when the unit’s power is turned off. This
displays the status of the battery. If the display says “OK,”
there is sufficient voltage. If the display says “LOW,” the
battery voltage has run down. Contact your nearby Roland
service station as soon as possible to have the battery
replaced.
internal memory when the unit’s power is turned off. This
displays the status of the battery. If the display says “OK,”
there is sufficient voltage. If the display says “LOW,” the
battery voltage has run down. Contact your nearby Roland
service station as soon as possible to have the battery
replaced.