Roland XV-5080. 用户手册
217
Chapter 10
Examples of Applications Using the XV-5080
Controlling the XV-5080 in
Real Time Using an External
MIDI Device
Real Time Using an External
MIDI Device
External MIDI controllers (modulation lever, foot switch,
expression pedal, etc.) can be used to modify Multi-effects
settings or Tone settings in real time.
expression pedal, etc.) can be used to modify Multi-effects
settings or Tone settings in real time.
Changing the Multi-Effects
Settings From an External MIDI
Device
Settings From an External MIDI
Device
The parameters that can be changed via MIDI are
predetermined according to the selected Multi-effects.
predetermined according to the selected Multi-effects.
This applies to the Multi-effects parameters described on p.
44 to p. 105 that have an appended “#” mark.
44 to p. 105 that have an appended “#” mark.
Settings can be made for each Patch, Performance, and
Rhythm Set.
Rhythm Set.
1. Select the Multi-effects you wish to use.
Make the settings in the Effects General page. For the setting
procedure, refer to Chapter 2 (p. 25).
procedure, refer to Chapter 2 (p. 25).
2. From the various Play pages, press buttons in the
following order to access the Effects MFX #2 page.
For Patches or Rhythm Sets
[F6 (Effects)] - [F3 (MFX Ctl)]
fig.10-001.e_70
For Performances or GM System
[F5 (Effects)] - [F3 (MFX Ctl)]
fig.10-002.e_70
Three different Multi-effects can be set for a Performance.
Press [F3 (MFX Ctl)] to switch among the MFX-A, MFX-B,
and MFX-C pages.
The MIDI channel used for controlling the three multi-effects
is determined according to the MFX Source setting (p. 31).
Setting MFX Source to "PERF" selects the Performance MFX
Ctrl Channel, and when set to "Part 1-32," the Receive
Channel settings for each part are used.
Press [F3 (MFX Ctl)] to switch among the MFX-A, MFX-B,
and MFX-C pages.
The MIDI channel used for controlling the three multi-effects
is determined according to the MFX Source setting (p. 31).
Setting MFX Source to "PERF" selects the Performance MFX
Ctrl Channel, and when set to "Part 1-32," the Receive
Channel settings for each part are used.
3. Press [
]/[
]/[
]/[
] to move the cursor to
the parameter you want to set.
* Hold down [SHIFT] and press [
] to move to the
parameter furthest to the left.
4. Either by rotating the VALUE dial or by pressing [INC]/
[DEC], set the value.
* If you’ve made a mistake, simply press [UNDO]. The value of
the parameter will be restored to what it was when you first
positioned the cursor there.
positioned the cursor there.
5. Press [EXIT] to return to the PLAY page.
* A “*” symbol will appear at the left of the group name,
indicating that the settings have been modified. If you wish to
keep the settings, you need to store them. (p. 194)
keep the settings, you need to store them. (p. 194)
* When the Performance SOURCE is set to a value of PART 1–
32, the Part name will appear in the upper right of the display.
This indicates that the parameters below are the parameters for
the Patch assigned to the Part.
This indicates that the parameters below are the parameters for
the Patch assigned to the Part.
MFX Control page ([PATCH] - [F6
(Effects)] - [F3 (MFX Ctl)]/
[PERFORM] - [F5 (Effects)] - [F3 (MFX
Ctl)])
(Effects)] - [F3 (MFX Ctl)]/
[PERFORM] - [F5 (Effects)] - [F3 (MFX
Ctl)])
MFX Control Source
Select the Control Source to be used for changing the Multi-
effects parameters, and set the Sens and parameters to be
changed by that Control Source.
effects parameters, and set the Sens and parameters to be
changed by that Control Source.
OFF:
No controller is used.
CC01–95:
Controller numbers 1–95 (except for 32)
PITCH BEND:
Pitch Bend
AFTERTOUCH:
Aftertouch
SYS-CTRL 1–4:
System control 1–4
MFX Control Sens -63– +63
If you wish to modify the selected parameter in a positive (+)
direction—i.e., a higher value, toward the right, or faster
etc.—from its current setting, select a positive (+) value. If
you wish to modify the selected parameter in a negative (-)
direction—i.e., a lower value, toward the left, or slower etc.—
from its current setting, select a negative (-) value. Higher
numbers produce a greater amount of change.
direction—i.e., a higher value, toward the right, or faster
etc.—from its current setting, select a positive (+) value. If
you wish to modify the selected parameter in a negative (-)
direction—i.e., a lower value, toward the left, or slower etc.—
from its current setting, select a negative (-) value. Higher
numbers produce a greater amount of change.