Roland XV-3080 用户手册
22
Chapter 2 Using the XV-3080 Effects
Routing Tones to Effects
Output (Tone Output)
This page allows you to route each Tone to the Multi-Effects
or to the desired rear-panel output jacks. It also lets you set
its output level and its send level to the Chorus and Reverb.
or to the desired rear-panel output jacks. It also lets you set
its output level and its send level to the Chorus and Reverb.
Output Assign
MFX:
The Tone is sent into the Multi-Effects. The Multi-
Effects unit has its own settings that route its output to
OUTPUT jacks
OUTPUT jacks
.
OUTPUT A–C:
The Tone is sent to one of the three output-
jack stereo pairs, OUTPUTS A–C.
INDIVIDUAL 1–6:
The Tone is sent to the INDIVIDUAL
mono output jacks 1–6.
Chorus (Chorus Send Level) 0–127
This sets how much of the Tone is sent to the Chorus.
Reverb (Reverb Send Level) 0–127
This sets how much of the Tone is sent to the Reverb.
Making Multi-Effects Settings
This page allows you to establish various settings for the
Multi-Effects unit, including its parameters and output-jack
assignment.
Multi-Effects unit, including its parameters and output-jack
assignment.
PATCH MFX TYPE
Use this parameter to select from among the 63 available
Multi-Effects. For a description of these effects, check out
“Parameters for Each Multi-Effect (MFX TYPE)” (p. 36).
Multi-Effects. For a description of these effects, check out
“Parameters for Each Multi-Effect (MFX TYPE)” (p. 36).
PATCH MFX PRM (Patch MFX
Parameter)
Parameter)
These parameters allow you to customize the selected Multi-
Effect. For a description of the parameters, check out
“Parameters for Each Multi-Effect (MFX TYPE)”p. 36.
Effect. For a description of the parameters, check out
“Parameters for Each Multi-Effect (MFX TYPE)”p. 36.
* You cannot select this page when “Type” on the PATCH
MFX TYPE page is set to THROUGH.
PATCH MFX CTRL (Patch MFX Control)
Select the Control Source to be used for changing the Multi-
Effects parameters, and set the Sens and parameters to be
changed by that Control Source.
Effects parameters, and set the Sens and parameters to be
changed by that Control Source.
* You cannot select this page when “Type” on the PATCH
MFX TYPE page is set to THROUGH.
Control 1–4 (MFX Control 1–4 Source)
OFF:
No controller is used.
CC01–95:
Controller numbers 1–95 (except for 32)
BENDER:
Pitch Bend
AFTERTOUCH:
Aftertouch
SYS-CTRL 1–4:
System control (Control 1–4)
Destination
This selects the Multi-Effects parameter to be controlled
using the MFX Control 1–4 source.
using the MFX Control 1–4 source.
Sens (MFX Control Sens) -63– +63
If you wish to modify the selected parameter in a positive (+)
direction – i.e., a higher value, toward the right, or faster etc.
– from its current setting, select a positive (+) value. If you
wish to modify the selected parameter in a negative (-)
direction – i.e., a lower value, toward the left, or slower etc. –
from its current setting, select a negative (-) value. Higher
numbers produce a greater amount of change.
direction – i.e., a higher value, toward the right, or faster etc.
– from its current setting, select a positive (+) value. If you
wish to modify the selected parameter in a negative (-)
direction – i.e., a lower value, toward the left, or slower etc. –
from its current setting, select a negative (-) value. Higher
numbers produce a greater amount of change.
PATCH MFX OUT (Patch MFX Output)
Output (Output Assign) A/B/C
This setting specifies the stereo pair of OUTPUT jacks to
which the stereo output of the Multi-Effects unit is routed.
which the stereo output of the Multi-Effects unit is routed.
Dry (Dry Output Level) 0–127
This sets the Multi-Effects unit’s output level to the selected
jacks.
jacks.
Chorus (Chorus Send Level) 0–127
This sets the amount of the Multi-Effect unit’s output to be
sent to the Chorus.
sent to the Chorus.
Reverb (Reverb Send Level) 0–127
This sets the amount of the Multi-Effect unit’s output to be
sent to the Reverb.
sent to the Reverb.