Roland VS-1824 用户手册
86
Chapter 6 Mixer Channel Strip Detail
This chapter explains in detail each of the settings available
in the Mixer display for the Input Mixer, Track Mixer, and
the Master Block. For general information about signal flow,
busses, etc., see Chapter 5, “Using The Digital Mixer.”
in the Mixer display for the Input Mixer, Track Mixer, and
the Master Block. For general information about signal flow,
busses, etc., see Chapter 5, “Using The Digital Mixer.”
Input Mixer
The following functions are found in the Input Mixer. Press
the SELECT button for any Input to view and adjust its
settings. Press the function button located under the display
corresponding to the setting you wish to change. Or, press
the SELECT button for any Input to view and adjust its
settings. Press the function button located under the display
corresponding to the setting you wish to change. Or, press
the [
], [
], [
], and [
] buttons to move the
cursor to the setting you wish to change. Use the TIME/
VALUE dial to select the desired value.
VALUE dial to select the desired value.
If you adjust the equalizer and the pan while sound is
playing, you may notice “blips” in the sound. This is not a
malfunction. If you find it annoying, adjust the equalizer and
the pan when the sound is not playing.
playing, you may notice “blips” in the sound. This is not a
malfunction. If you find it annoying, adjust the equalizer and
the pan when the sound is not playing.
[F1 (MIX)] MIX Bus Enable/Pan
Sets the panning of the signal (L63-R63) sent to the MIX bus.
(Mix Assign Switch)
On:
The channel is assigned directly to the MIX bus. Set this
to “on” when you simply want to mix an input without
actually recording it.
to “on” when you simply want to mix an input without
actually recording it.
Off:
The channel is not assigned to the MIX bus.
(Pan Knob)
Sets the left-right balance (L63-R63) of the channel in the MIX
bus.
bus.
[F2 (Low)], [F3 (Mid)], and
[F4 (High)] Equalizer
[F4 (High)] Equalizer
Sw (Equalizer Switch)
Turns the EQ on and off. The EQ switch must be ON to make
settings in the EQ section.
settings in the EQ section.
(Equalizer Select)
This setting selects how many bands of EQ are available in
the channel.
the channel.
2 Band EQ:
Low and High bands are available.
3 Band EQ:
Low, Mid, and High bands are available.
You can use three-band EQ on as many as 16 tracks and/or
inputs at the same time. Three-band EQ cannot be used on
Tracks 17 and 18. Two-band EQ can be used on all 28 tracks
and inputs at the same time.
inputs at the same time. Three-band EQ cannot be used on
Tracks 17 and 18. Two-band EQ can be used on all 28 tracks
and inputs at the same time.
Low
This adjusts the gain (-12 dB to +12 dB) and the shelving
frequency (40 Hz-1.5 kHz) of the low-band EQ.
frequency (40 Hz-1.5 kHz) of the low-band EQ.
Mid
This adjusts the gain (-12 dB to +12 dB) and the center
frequency (200 Hz-8 kHz), and the Q (filter sharpness) (0.5-
16) of the mid-band EQ. The Mid band is not available when
“2 Band EQ” is selected.
frequency (200 Hz-8 kHz), and the Q (filter sharpness) (0.5-
16) of the mid-band EQ. The Mid band is not available when
“2 Band EQ” is selected.
High
This adjusts the gain (-12 dB to +12 dB) and the shelving
frequency (500 Hz-18 kHz) of the high-band EQ.
frequency (500 Hz-18 kHz) of the high-band EQ.
ENTER Button
When the cursor is positioned inside the EQ section, the
ENTER button will be blinking. Press [ENTER] to view a
graphic display of the EQ settings.
ENTER button will be blinking. Press [ENTER] to view a
graphic display of the EQ settings.
[F6 (PRM.V)] Parameter View/
[F6 (CH.V)] Channel View
[F6 (CH.V)] Channel View
This changes the display from Channel View to Parameter
View. Press [F6 (PRM.V)] to view the parameter settings
(such as Pan or Effect Send) for all channels. Press [F6
(CH.V)] to view all of the mixer settings for just one channel.
View. Press [F6 (PRM.V)] to view the parameter settings
(such as Pan or Effect Send) for all channels. Press [F6
(CH.V)] to view all of the mixer settings for just one channel.
[F1 (FX1)] Effect 1 Send
Channel settings for the EFFECT 1 Bus. Sets the Effect Send
Switch, the Send Level (0-127) and panning.
Switch, the Send Level (0-127) and panning.
Sw (Effect Send Switch)
Switches the channel to the EFFECT bus.
Off:
The channel is not sent to the EFFECT bus.
Pre:
The signal is sent to the EFFECT bus before it passes
through the mixer fader.
through the mixer fader.
Post:
The signal is sent to the EFFECT bus after it passes
through the mixer fader.
through the mixer fader.
Level
Sets the send level (0-127) of the signal sent to the EFFECT 1
Bus.
Bus.
Panning
Sets the panning (L63-R63) of the signal sent to the EFFECT 1
Bus.
Bus.