Roland RD-700SX 用户手册

 

If the RD-700SX does not function in the way you expect, first check 
the following points. If this does not resolve the problem, consult your 
dealer or a nearby Roland Service Station.

 

Power Not 
Coming On

 

Is the RD-700SX’s power cord properly 
plugged into a power source as well as 
connected to the RD-700SX?

 

No Sound

 

Is the power for connected amps and 
speakers turned on? Is the volume turned 
all the way down?

Is the VOLUME slider turned all the way 
down?

Are all connections properly made?
• When using the RD-700SX as a stand-

alone instrument, be sure to connect 
with audio cables or use headphones 
(p. 21).

Are sounds audible with headphones 
connected? 
• If sounds are audible through 

headphones, it may indicate that there 
is a short in an audio cable or some sort 
of amp or mixer problem. Check the 
cables and equipment once again.

Is ZONE SWITCH set to OFF? 
(p. 41, p. 64)

Is a Part’s volume turned off with the 
ZONE LEVEL slider? (p. 41, p. 64)

If the sound for a pressed key does is not 
being played, is the Local Switch set to 
OFF? 
• In the Utility Rec Setting in Edit mode, 

Are the effect settings correct? 
Check following settings.
• ON/OFF settings for MULTI EFFECTS 

• Other Multi-Effect settings in Edit 

Are the Wave Expansion Boards correctly 
installed? 
• When selecting settings while using the 

EXPANSION [A] or [B] Tones or 
Rhythm Sets, confirm that the specified 
Wave Expansion Boards are properly 
installed in the specified slots (p. 15).

Has the volume been lowered by pedal 
operations or by MIDI messages (volume 
messages or expression messages) 
received from an external MIDI device?

 

No Sound for 
Specific Part

 

Is the Part’s volume level turned down? 
Check following settings.
• ZONE LEVEL sliders (p. 41, p. 64) 
• Part Parameter Volume settings in Edit 

Are the Part’s MIDI Receive channel and 
the MIDI Transmit channel for the 
connected MIDI device matched? 
Check the MIDI Receive channel settings 
with Part Parameter Receive Channel in 
Edit mode (p. 92).

 

No Sound From 
the Connected 
MIDI Device

 

Is the device enabled to transmit MIDI 
messages? 
• Set [EXTERNAL/INTERNAL] and 

ZONE SWITCH to ON (p. 64). MIDI 
messages cannot be transmitted if 
ZONE SWITCH is set to OFF.

Is the RD-700SX’s keyboard controller 
section MIDI Transmit channel matched 
to the connected MIDI device’s MIDI 
Receive channel? 
• Make the Ch(MIDI Transmit Channel) 

 

No Sound in a 
Specific Range

 

Has the range in which sounds are to be 
played (the key range) been set? 
Check following settings.
• Settings for the LWR and UPR Parts in 

With certain Tones, for example Rhythm 
Sets, bass Tones, Timpani, and other 
Tones will not sound if a portion of the 
Tone falls outside the recommended 
range.

Is V-Link switched on (p. 97)? 
• Set the Local ON/OFF to ON in the V-

Link Setting in Edit mode.
Sounds are played with keyboard even 
when V-Link is switched on.

 

Tones Are 
Altered

 

Did you call up a Setup? 
• When a Setup is called up, the current 

Tone, effect, and other settings are 
disabled, and the selected Setup goes 
into effect (p. 56). Resave required 
settings to a Setup (p. 58).

Did you press ONE TOUCH [PIANO] or 
[E.PIANO]? 
• When ONE TOUCH [PIANO] or 

[E.PIANO] is pressed, the current Tone, 
effect, and other settings are disabled, 
and settings for use in piano 
performances go into effect (p. 32). 
Resave required settings to a Setup (p. 
58).

RD-700SX_e.book 108 ページ ２００６年３月２３日　木曜日　午後２時５２分