Roland GW-7 用户手册
9
Introduction
1.
Remove the GW-7 from its shipping carton, and place it on
a horizontal surface.
a horizontal surface.
2.
Connect the included power supply cord to the included AC
adaptor.
adaptor.
fig.ACadap
Depending on your region, the included AC adaptor may be a
different type than the one shown above. If so, omit step 2 and
proceed.
different type than the one shown above. If so, omit step 2 and
proceed.
3.
Connect the AC adaptor to the DC IN jack on the GW-7’s
rear panel, and then plug the AC adaptor into an electrical
outlet.
rear panel, and then plug the AC adaptor into an electrical
outlet.
To prevent the inadvertent disruption of power to your unit
(should the plug be pulled out accidentally), and to avoid
applying undue stress to the AC adaptor jack, anchor the power
cord using the cord hook, as shown in the illustration.
(should the plug be pulled out accidentally), and to avoid
applying undue stress to the AC adaptor jack, anchor the power
cord using the cord hook, as shown in the illustration.
fig.codef
Once the connections have been completed, turn on power to
your various devices in the order specified. By turning on
devices in the wrong order, you risk causing malfunction and/
or damage to speakers and other devices.
your various devices in the order specified. By turning on
devices in the wrong order, you risk causing malfunction and/
or damage to speakers and other devices.
1.
Before you turn on the power, turn the VOLUME knob all the
way to the left to minimize the volume.
way to the left to minimize the volume.
2.
Press the rear panel POWER button to turn on the power.
This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will
operate normally.
(a few seconds) after power up is required before the unit will
operate normally.
If the GW-7 is connected to a keyboard amp or audio amp, turn
on the power of the GW-7 first, and then switch on your amp.
on the power of the GW-7 first, and then switch on your amp.
3.
Turn the VOLUME knob to adjust the volume of the GW-7.
1.
Press the POWER switch once again to turn off the power.
If the GW-7 is connected to a keyboard amp or audio amp,
switch off the power to your amp first, then turn off the power
on the GW-7.
switch off the power to your amp first, then turn off the power
on the GW-7.
Hold down [FUNCTION] and turn the VALUE dial.
1.
Hold down [SHIFT] and press [EXIT] (DEMO).
The screen will indicate “DEMO PLAY.”
2.
Press [START/STOP] to begin demo playback.
3.
Press [START/STOP] to stop demo playback.
4.
Press [EXIT] to return to the previous screen.
All rights reserved. Unauthorized use of this material for
purposes other than private, personal enjoyment is a violation
of applicable laws.
purposes other than private, personal enjoyment is a violation
of applicable laws.
No data for the music that is played will be output from MIDI
OUT.
OUT.
Immediately after you turn on the power, the GW-7 will be in a state
where you can use the entire keyboard to play a piano sound. The
GW-7’s keyboard can operate in one of the following three modes.
where you can use the entire keyboard to play a piano sound. The
GW-7’s keyboard can operate in one of the following three modes.
1.
Turn on the power as described in “Turning the Power On”
A piano sound will be selected.
2.
Select the desired Tone.
1.
Press MODE [TONE] so the button is lit.
2.
Turn the VALUE dial to step through the Tones one by
one. Alternatively, you can press one of the ten buttons
[PIANO]–[DRUMS] to select a Tone by category.
one. Alternatively, you can press one of the ten buttons
[PIANO]–[DRUMS] to select a Tone by category.
3.
Play the keyboard.
Turn the VOLUME knob to adjust the volume.
Connecting the AC Adaptor
Turning the Power On/Off
Turning the Power On
to an AC outlet
AC adaptor
Power supply cord
GW-7 rear panel
Cord hook
Turning the Power Off
Adjusting the Screen Contrast
Listening to the Demo Song
Playing Sounds from the
Keyboard (Keyboard Mode)
MAIN
The entire keyboard plays one Tone.
SPLIT
The region of the keyboard to the left of the split point
becomes the
becomes the
Lower Part
, while the region of the key-
board to the right of the split point becomes the
Upper
Part
. Each part plays a different Tone.
DUAL
The entire keyboard plays two Tones simultaneously.
Using Main Mode
GW-7_e.book 9 ページ ２００５年２月１６日 水曜日 午前８時４８分