Roland HandSonic 10 用户手册
27
Advanced Edit
5.
Continuing to press the [
] will give you access to
the following parameters.
Normally you do not have to adjust them, as the settings
are automatically changed depending on your choice of
pads (listed previously).
are automatically changed depending on your choice of
pads (listed previously).
For detailed explanations of the above trigger parameters,
please see Glossary (p. 38).
please see Glossary (p. 38).
1.
While holding down the [SHIFT] button, press [EDIT].
Press the [
Press the [
] until you see <MIDI>.
Changes to any of the following parameters are only
needed if you are using the HandSonic to control an
external sound module or in exceptional situations.
needed if you are using the HandSonic to control an
external sound module or in exceptional situations.
2.
Press the [ ], and here you see:
3.
Press the [
] to access the following parameters.
Local Control
Turn this off when recording your HandSonic performance
on an external sequencer, as long as you are also
receiving the MIDI signal FROM that sequencer.
on an external sequencer, as long as you are also
receiving the MIDI signal FROM that sequencer.
PC Tx/Rx
This allows the HandSonic to transmit & receive “Program
Change” information.
Change” information.
CC Tx/Rx
Determines if you want to send or receive control changes.
(like pressure information etc..)
(like pressure information etc..)
Pressure Control Change Number
(For details on PAf, see Glossary
D BEAM Control Change Number
Knob Control Change Number
* Control change information is ONLY transmitted from the
knob when it is in the EFFECT position (LED is lit). Use this
when you want to control an external MIDI module. If the
HandSonic receives this information via MIDI, nothing will
happen.
when you want to control an external MIDI module. If the
HandSonic receives this information via MIDI, nothing will
happen.
Device ID
1.
While holding down the [SHIFT] button, press [EDIT].
Press the [
Press the [
] until you see <BULK DUMP>.
Used for saving the HandSonic settings to an external
sequencer.
sequencer.
Press the [
], then use tha [+]/[-] button to select the type.
Choices are: 1 KIT, ALL KITS, ALL
To execute, press the [
] again, and a confirmation
message will appear in the display. Press the [4](ok) button
if OK, and the [2](cancel) button to cancel the operation.
if OK, and the [2](cancel) button to cancel the operation.
* Saving/Re-Loading individual kits example: If you save
Kit #1, and then later want to re-load it, select the
destination for that kit BEFORE loading. It will not
automatically be loaded into the Kit #1 position.
destination for that kit BEFORE loading. It will not
automatically be loaded into the Kit #1 position.
1.
While holding down the [SHIFT] button, press [EDIT].
Press the [
Press the [
] until you see <FACTORY RESET>.
Press the [
], then use tha [+]/[-] button to select the type.
The choices here are
SETUP
,
ALL KITS
,
ALL
To execute, press the [
] again, and a confirmation
message will appear in the display. Press the [4](ok) button
if OK, and the [2](cancel) button to cancel the operation.
if OK, and the [2](cancel) button to cancel the operation.
* This resets all parameters to the original factory version.
You can not use Undo after executing this function. Make
sure you save your settings first. (Bulk Dump)
sure you save your settings first. (Bulk Dump)
Display
Range/Choices
Sens
(Sensitivity)
(Sensitivity)
1–16
Threshold
0–15
Curve
LINEAR, EXP1, EXP2, LOG1, LOG2,
SPLINE, LOUD1, LOUD2
SPLINE, LOUD1, LOUD2
Scan Time
0–4
Retrig Cancel
1–16
Mask Time
0–64
XTalk Cancel
OFF, 20–80
Rim Sens
OFF, 1–20
Rim Gain
0.5–2.0
MIDI
BULK DUMP
FACTORY RESET
HPD-10_e1.book 27 ページ ２００６年４月７日 金曜日 午後２時１４分