Roland SH-201 用户手册
60
Parameter list
Here’s a list of all the SH-201’s parameters.
The right column of the list (the panel operation column) shows how to set parameters that are accessible from
the panel of the SH-201 itself.
The right column of the list (the panel operation column) shows how to set parameters that are accessible from
the panel of the SH-201 itself.
You can use SH-201 Editor (p. 56) when you want to create sounds in greater detail, or to create your own
original arpeggios.
original arpeggios.
* The values listed are the ones that appear in the screen of SH-201 Editor.
OSC MIX/MOD parameters
Parameter
Value
Explanation
Panel operation
OSC1
WAVEFORM
SAW, SQR, PW-SQR,
TRI, SIN, NOISE,
FB-OSC, SUPER-SAW,
EXT-IN
TRI, SIN, NOISE,
FB-OSC, SUPER-SAW,
EXT-IN
Selects the waveform that is the basis of the sound.
PITCH WIDE
OFF, ON
Expands the range of the PITCH knob by three times.
PITCH
-36– +36
Adjusts the pitch in semitone steps.
DETUNE
-50– +50
Adjusts the pitch in one-cent steps.
PW/FEEDBACK
0–127
•
When WAVEFORM is “PW-SQR”
Specifies the width of the upper portion of the square
wave.
wave.
•
When WAVEFORM is “FB-OSC”
Specifies the amount of output sound that is returned
(fed back) to the input.
(fed back) to the input.
•
When WAVEFORM is “SUPER-SAW”
specifies the amount of pitch spread between the sev-
en sawtooth waves layered within a single oscillator.
en sawtooth waves layered within a single oscillator.
Turn the PW/FEEDBACK knob
(p. 30)
(p. 30)
OSC2
WAVEFORM
SAW, SQR, PW-SQR,
TRI, SIN, NOISE,
FB-OSC, SUPER-SAW,
EXT-IN
TRI, SIN, NOISE,
FB-OSC, SUPER-SAW,
EXT-IN
Selects the waveform that is the basis of the sound.
PITCH WIDE
OFF, ON
Expands the range of the PITCH knob by three times.
PITCH
-36– +36
Adjusts the pitch in semitone steps.
DETUNE
-50– +50
Adjusts the pitch in one-cent steps.
PW/FEEDBACK
0–127
•
When WAVEFORM is “PW-SQR”
Specifies the width of the upper portion of the square
wave.
wave.
•
When WAVEFORM is “FB-OSC”
Specifies the amount of output sound that is returned
(fed back) to the input.
(fed back) to the input.
•
When WAVEFORM is “SUPER-SAW”
specifies the amount of pitch spread between the sev-
en sawtooth waves layered within a single oscillator.
en sawtooth waves layered within a single oscillator.
Turn the PW/FEEDBACK knob
(p. 30)
(p. 30)
PITCH ENV
A
0–127
Specifies the time from when you play a key until the
pitch reaches the highest (or lowest) point.
pitch reaches the highest (or lowest) point.
Move the PITCH ENV A slider
(p. 31)
(p. 31)
D
0–127
Specifies the time from when the pitch reaches its high-
est (or lowest) point until it returns to the pitch of the key
you pressed.
est (or lowest) point until it returns to the pitch of the key
you pressed.
Move the PITCH ENV D slider
(p. 31)
(p. 31)
OSC1 DEPTH
-63– +63
Specifies the direction and amount of the OSC 1’s pitch
change.
change.
OSC2 DEPTH
-63– +63
Specifies the direction and amount of the OSC 2’s pitch
change.
change.
MIX/MOD
MIX/MOD
TYPE
TYPE
MIX, SYNC, RING
Selects how OSC 1 and OSC 2 are to be combined.
Press the MIX/MOD TYPE but-
ton (p. 32)
ton (p. 32)
BALANCE
-63– +63
Adjusts the volume balance of OSC 1 and OSC 2.
LOW FREQ
CUT, FLAT, BOOST
Selects whether the low frequency range will be boosted
or cut.
or cut.
SH-201_r_e.book 60 ページ ２００６年４月２７日 木曜日 午前１１時２８分