Roland VH-11 用户手册

  

This product complies with the requirements of European Directive 89/336/EEC.

 

291a

 

354a

 

• Do not expose the unit to direct sunlight, place it near 

devices that radiate heat, leave it inside an enclosed 
vehicle, or otherwise subject it to temperature extremes. 
Excessive heat can deform or discolor the unit.

 

355b

 

• When moved from one location to another where the 

temperature and/or humidity is very different, water 
droplets (condensation) may form inside the unit. Damage 
or malfunction may result if you attempt to use the unit in 
this condition. Therefore, before using the unit, you must 
allow it to stand for several hours, until the condensation 
has completely evaporated.

 

356

 

• Do not allow rubber, vinyl, or similar materials to remain 

on the unit for long periods of time. Such objects can 
discolor or otherwise harmfully affect the finish.

 

401a

 

• For everyday cleaning wipe the unit with a soft, dry cloth 

or one that has been slightly dampened with water. To 
remove stubborn dirt, use a cloth impregnated with a mild, 
non-abrasive detergent. Afterwards, be sure to wipe the 
unit thoroughly with a soft, dry cloth.

 

402

 

• Never use benzine, thinners, alcohol or solvents of any 

kind, to avoid the possibility of discoloration and/or defor-
mation.

 

553

 

• Use a reasonable amount of care when using the unit’s 

buttons, sliders, or other controls; and when using its jacks 
and connectors. Rough handling can lead to malfunctions.

 

556

 

• When connecting / disconnecting all cables, grasp the 

connector itself—never pull on the cable. This way you will 
avoid causing shorts, or damage to the cable’s internal 
elements.

 

558a

 

• To avoid disturbing your neighbors, try to keep the unit’s 

volume at reasonable levels. You may prefer to use 
headphones, so you do not need to be concerned about 
those around you (especially when it is late at night).

 

558d

 

• This instrument is designed to minimize the extraneous 

sounds produced when it’s played. However, since sound 
vibrations can be transmitted through floors and walls to a 
greater degree than expected, take care not to allow these 
sounds to become a nuisance to neighbors, especially when 
performing at night and when using headphones.

 

559a

 

• When you need to transport the unit, package it in the box 

(including padding) that it came in, if possible. Otherwise, 
you will need to use equivalent packaging materials.

 

add

 

• The hi-hat stand is supported by means of a tripod. When 

installing the hi-hat, make sure the legs of the tripod are 
opened wide enough to keep the equipment from falling 
over.

 

add

 

• The hi-hat’s rubber surface may turn white, but this has no 

effect on the hi-hat’s function.

 

add

 

• Do not remove the special VH-11 clutch from the hi-hat or 

disassemble the clutch.

 

add

 

• When not using the hi-hat for extended periods, store the 

hi-hat in the open position to prevent placing any stress on 
the motion sensor unit.

 

add

 

• High-precision sensors are located at the portion of the 

motion sensor unit indicated by the arrow in the left figure 
below. Take care not to subject this area to excessive shock, 
and do not allow any foreign objects to enter any gaps.

 

fig.SensorNote

 

add

 

• Over long periods of use, the portion of the motion sensor 

unit that comes into contact with the hi-hat (the damper) 
may become worn at the points indicated by the arrows in 
the right figure above.
Such damper wear may prevent proper adjustment of the 
offset and may cause the hi-hat to swing with an unnatural 
motion. If this occurs, replace the damper. For more infor-
mation on replacing the damper, contact Roland Service.

VH-11_e 3 ページ ２００５年４月１２日　火曜日　午後１時２０分