Cypress CY7C1522AV18 用户手册

72-Mbit DDR-II SIO SRAM 2-Word

Burst Architecture

•

198 Champion Court

•

San Jose

,

CA 95134-1709

•

408-943-2600

Document #: 001-06981 Rev. *D

 Revised June 14, 2008

■

72-Mbit density (8M x 8, 8M x 9, 4M x 18, 2M x 36)

■

300 MHz clock for high bandwidth

■

2-word burst for reducing address bus frequency 

■

Double Data Rate (DDR) interfaces 
(data transferred at 600 MHz) at 300 MHz 

■

Two input clocks (K and K) for precise DDR timing

❐

SRAM uses rising edges only

■

Two input clocks for output data (C and C) to minimize clock 
skew and flight time mismatches

■

Echo clocks (CQ and CQ) simplify data capture in high-speed 
systems

■

Synchronous internally self-timed writes

■

DDR-II operates with 1.5 cycle read latency when the DLL is 
enabled

■

Operates similar to a DDR-I device with 1 cycle read latency in 
DLL off mode

■

1.8V core power supply with HSTL inputs and outputs

■

Variable drive HSTL output buffers

■

Expanded HSTL output voltage (1.4V–V

DD

)

■

Available in 165-Ball FBGA package (15 x 17 x 1.4 mm)

■

Offered in both Pb-free and non Pb-free packages

■

JTAG 1149.1 compatible test access port

■

Delay Lock Loop (DLL) for accurate data placement

CY7C1522AV18 – 8M x 8

CY7C1529AV18 – 8M x 9

CY7C1523AV18 – 4M x 18

CY7C1524AV18 – 2M x 36

The CY7C1522AV18, CY7C1529AV18, CY7C1523AV18, and
CY7C1524AV18 are 1.8V Synchronous Pipelined SRAMs,
equipped with Double Data Rate Separate IO (DDR-II SIO)
architecture. The DDR-II SIO consists of two separate ports: the
read port and the write port to access the memory array. The
read port has data outputs to support read operations and the
write port has data inputs to support write operations. The DDR-II
SIO has separate data inputs and data outputs to completely
eliminate the need to “turn-around” the data bus required with
common IO devices. Access to each port is accomplished
through a common address bus. Addresses for read and write
are latched on alternate rising edges of the input (K) clock. Write
data is registered on the rising edges of both K and K. Read data
is driven on the rising edges of C and C if provided, or on the
rising edge of K and K if C/C are not provided. Each address
location is associated with two 8-bit words in the case of
CY7C1522AV18, two 9-bit words in the case of CY7C1529AV18,
two 18-bit words in the case of CY7C1523AV18, and two 36-bit
words in the case of CY7C1524AV18 that burst sequentially into
or out of the device. 

Asynchronous inputs include an output impedance matching
input (ZQ). Synchronous data outputs are tightly matched to the
two output echo clocks CQ/CQ, eliminating the need to capture
data separately from each individual DDR-II SIO SRAM in the
system design. Output data clocks (C/C) enable maximum
system clocking and data synchronization flexibility.

All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the C or C (or K or K in a single clock
domain) input clocks. Writes are conducted with on-chip
synchronous self-timed write circuitry.

Maximum Operating Frequency 

300

278

250

200

167

MHz

Maximum Operating Current 

x8

900

855

800

700

650

mA

x9

900

855

800

700

650

x18

950

880

800

700

650

x36

1080

1000

900

750

650