Roland Fantom-S88 用户手册
131
Editing a Sample
Editing a Sample
Amp
This operation applies an envelope (time-variant change) to the
volume of the sample.
You can also adjust the volume of the entire sample.
volume of the sample.
You can also adjust the volume of the entire sample.
* You cannot execute this with more than one sample selected.
1.
Press [SAMPLE EDIT] to access the Sample Edit screen.
2.
Press [3 (Sample Modify)] to access the Sample Modify
window.
3.
Press [4 (Amp)].
fig.Amp_50
4.
Use VALUE dial or [INC], [DEC] to set the value.
•
Rate 1–4:
Specifies the rate of volume boost.
This specifies how much boost will be applied relative to the
current volume. The entire sample you select will be boosted.
current volume. The entire sample you select will be boosted.
Value:
0–400%
5.
If you want to specify a point, press [5 (Point)] to add a
check mark. Press
or
to select a parameter, and
then use VALUE dial or [INC], [DEC] to set the value.
•
Current Point:
Specifies the currently selected point. Beginning
near the start point, the points will be numbered 1, 2, 3, or 4.
•
Point 1–4:
Location of the current point
•
Rate 1–4:
Amplification ratio of the current point
Specifies how the volume of each point is to be boosted relative
to the current value.
to the current value.
Value:
0–400%
6.
If you want the edited sample to replace the current sample,
press [6 (Over Writer)] to display the “
✔
” mark.
7.
Press [8 (Exec)].
A message will ask you for confirmation.
8.
To execute, press [8 (Exec)].
* To cancel, press [7 (Cancel)].
Stretching or Shrinking a
Sample (Time Stretch)
This operation stretches or shrinks the sample to modify the length
or tempo. You can stretch or shrink the sample by a factor of one half
to double the original length.
or tempo. You can stretch or shrink the sample by a factor of one half
to double the original length.
* You cannot execute this with more than one sample selected.
1.
Press [SAMPLE EDIT] to access the Sample Edit screen.
2.
Press [3 (Sample Modify)] to access the Sample Modify
window.
3.
Press [5 (Time Strtch)].
fig.TimeStretch_50
4.
Press
or
to select the parameter.
•
Edit Time Stretch
BPM:
Change the BPM (p. 116) of the sample to the BPM you
specify.
specify.
Time:
Specify the length of the sample as a time value.
Rate:
Specify the length relative to the current length of the
sample.
sample.
Value:
50.0–200.0%
•
Type
Lower settings of this value will make the sound more suitable
for faster phrases, and higher settings will make the sound more
suitable for slower phrases.
for faster phrases, and higher settings will make the sound more
suitable for slower phrases.
Value:
TYPE01–TYPE10
•
Quality Adjust
Make fine adjustments to the tonal quality of the Time Stretch.
Value:
1–10
5.
Use VALUE dial or [INC/DEC] to specify the tempo/length.
When setting the BPM (tempo) value, you can hold down
[SHIFT] and turn the VALUE dial, or use [INC] [DEC] to adjust
the value to the right of the decimal point.
[SHIFT] and turn the VALUE dial, or use [INC] [DEC] to adjust
the value to the right of the decimal point.
6.
Press [8 (Exec)].
The length of the sample will be changed as specified.
* To cancel, press [7 (Cancel)].
Reference_e.book 131 ページ 2003年7月14日 月曜日 午後3時25分