Roland Fantom-S88 用户手册
207
Expanding the Memory
Expanding the Memory
The Fantom-S/Fantom-S88 comes with 32 MB of memory into which
audio samples can be loaded. However, in some cases, 32 MB of
memory will be insufficient for loading large amounts of data. In
such a case, you will have to add separately sold memory (DIMM).
Memory can be expanded up to 64/128/256/512 MB.
audio samples can be loaded. However, in some cases, 32 MB of
memory will be insufficient for loading large amounts of data. In
such a case, you will have to add separately sold memory (DIMM).
Memory can be expanded up to 64/128/256/512 MB.
Before expanding the memory, consult with your retailer, the nearest
Roland Service Center, or an authorized Roland distributor.
Roland Service Center, or an authorized Roland distributor.
* If a 512 MB DIMM is installed, the result will be the same as if a 256
Precautions for Expanding
Memory
901
• To avoid the risk of damage to internal components that can be
caused by static electricity, please carefully observe the following
whenever you handle the board.
whenever you handle the board.
1
• Before you touch the board, always first grasp a metal object
(such as a water pipe), so you are sure that any static
electricity you might have been carrying has been discharged.
electricity you might have been carrying has been discharged.
2
• When handling the board, grasp it only by its edges. Avoid
touching any of the electronic components or connectors.
5
• Save the bag in which the board was originally shipped, and
put the board back into it whenever you need to store or
transport it.
transport it.
• Use a Philips screwdriver that is suitable for the size of the screw
(a number 2 screwdriver, Fantom-S only). If an unsuitable screw-
driver is used, the head of the screw may be stripped.
driver is used, the head of the screw may be stripped.
• To remove a screw, rotate the screwdriver counter-clockwise. To
tighten the screws, rotate the screwdriver clockwise.
fig.Screw.e
• Be careful that the screws you remove do not drop into the
interior of the Fantom-S/S88.
• Be careful not to cut your hand on the edge of the cover or the
opening edge while removing the cover.
911
• Do not touch any of the printed circuit pathways or connection
terminals.
912
• Never use excessive force when installing a circuit board. If it
doesn’t fit properly on the first attempt, remove the board and try
again.
again.
913
• When circuit board installation is complete, double-check your
work.
914 (Modified)
• Always turn the unit off and unplug the power cord before
attempting installation of the memory DIMM board.
915 (Modified)
• Install only the specified memory DIMM board. Remove only the
928
• When turning the unit upside-down, get a bunch of newspapers
or magazines, and place them under the four corners or at both
ends to prevent damage to the buttons and controls. Also, you
should try to orient the unit so no buttons or controls get
damaged.
ends to prevent damage to the buttons and controls. Also, you
should try to orient the unit so no buttons or controls get
damaged.
929
• When turning the unit upside-down, handle with care to avoid
dropping it, or allowing it to fall or tip over.
• Do not leave the bottom cover removed. After installation of the
memory module is complete, be sure to replace the cover.
How to Expand the Memory
Install the memory module after removing the bottom panel cover.
1.
Before expanding the memory, turn off the power of the
Fantom-S/S88 and all connected devices, and disconnect
all cables, including the Power cable, from the Fantom-S/
S88.
2.
From the Fantom-S/S88, remove only the screws shown in
the following diagram, and detach the cover. On the
Fantom-S, the cover is located on the bottom panel. On the
Fantom-S88, it is located on the front panel. From the
Fantom-S/S88, remove only the screws shown in the
following diagram, and detach the cover.
fig.18-02.e
* A hex wrench is included with the Fantom-S88. When
removing screws, you must use this hex wrench.
fig.Dimm-05
3.
Press outward the white clips at either end of the socket
should be in the downward position.
fig.DIMM-01
tighten
loosen
Screws to be removed