Roland Fantom-S88 用户手册
99
Modifying the Sound in Real Time
Modifying the Sound in Real Time
Assignable Type
Specifies the function controlled by the D Beam controller.
Value
CC01–31, 33–95:
Controller numbers 1–31, 33–95
For more information about Control Change messages, please
refer to
refer to
“MIDI Implementation”
(Parameter List).
Bend Up:
Raises the pitch in semitone steps
(up to 4 octaves higher).
(up to 4 octaves higher).
Bend Down:
Lowers the pitch in semitone steps
(up to 4 octaves lower).
(up to 4 octaves lower).
Start/stop:
Starts/Stops the sequencer.
TAP Tempo:
Tap tempo
(a tempo specified by the interval at which you
move your hand over the D Beam controller).
(a tempo specified by the interval at which you
move your hand over the D Beam controller).
Arp Grid:
Arpeggio Grid
Arp Duration:
Arpeggio Duration
Arp Motif:
Arpeggio Motif
Arp Oct Up:
The range in which the arpeggio is sounded will
rise in steps of an octave (maximum 3 octaves).
rise in steps of an octave (maximum 3 octaves).
Arp Oct Down:
The range in which the arpeggio is sounded will
lower in steps of an octave (maximum 3 octaves).
lower in steps of an octave (maximum 3 octaves).
Range Min (D Beam Range Lower)
Specify the lower limit of the range of the D Beam controller.
Value:
0–127
Range Max (D Beam Range Upper)
Specify the upper limit of the range of the D Beam controller.
By setting Range Max below Range Min you can invert the range of
change.
By setting Range Max below Range Min you can invert the range of
change.
Value:
0–127
Settings for the ASSIGNABLE are saved independently for each
performance as part of the performance settings. This lets you create
performances that make effective use of controller settings.
performance as part of the performance settings. This lets you create
performances that make effective use of controller settings.
If Patch mode is selected, this is saved as part of the system settings.
If you want to save the settings, press [8 (System Write)].
If you want to save the settings, press [8 (System Write)].
PAD Trigger settings
(Pad-related settings)
(Pad-related settings)
You can use the D Beam controller to control the pads as an
alternative to striking the pads themselves.
alternative to striking the pads themselves.
1.
Hold down [JUMP] and press D BEAM [PAD TRIGGER].
The Pad Trigger Screen appears.
fig.13-02c_50
2.
Move the cursor to the parameter that you want to set, and turn
the VALUE dial or press [INC]/[DEC] to make the setting.
3.
Press [EXIT] the Pad Trigger screen will close.
Pad Number
Specifies the pad number affected by the D Beam.
Value:
0–16
Pad Velocity
Specifies the strength of the pad sound played by the D Beam
controller.
controller.
Value:
1–127
Pad Control Mode
This specifies how the D Beam will behave when it is obstructed. If
this is set to MOMENTARY, the parameter will be on only while the
D Beam is obstructed, and will turn off when you stop obstructing it.
If this is set to LATCH, the parameter will alternately be switched
on/off each time you obstruct the D Beam.
this is set to MOMENTARY, the parameter will be on only while the
D Beam is obstructed, and will turn off when you stop obstructing it.
If this is set to LATCH, the parameter will alternately be switched
on/off each time you obstruct the D Beam.
Value:
MOMENTARY, LATCH
Settings for the PAD trigger are saved independently for each
performance as part of the performance settings. This lets you create
performances that make effective use of controller settings.
performance as part of the performance settings. This lets you create
performances that make effective use of controller settings.
If Patch mode is selected, this is saved as part of the system settings.
If you want to save the settings, press [8 (System Write)].
If you want to save the settings, press [8 (System Write)].
Reference_e.book 99 ページ ２００３年７月１４日 月曜日 午後３時２５分