Nxp Semiconductors UM10237 用户手册
UM10237_2
© NXP B.V. 2008. All rights reserved.
User manual
Rev. 02 — 19 December 2008
447 of 792
NXP Semiconductors
UM10237
Chapter 17: LPC24XX Universal Asynchronous Receiver/Transmitter
4.1 UART1 Receiver Buffer Register (U1RBR - 0xE001 0000, when
DLAB = 0 Read Only)
The U1RBR is the top byte of the UART1 RX FIFO. The top byte of the RX FIFO contains
the oldest character received and can be read via the bus interface. The LSB (bit 0)
represents the “oldest” received data bit. If the character received is less than 8 bits, the
unused MSBs are padded with zeroes.
the oldest character received and can be read via the bus interface. The LSB (bit 0)
represents the “oldest” received data bit. If the character received is less than 8 bits, the
unused MSBs are padded with zeroes.
The Divisor Latch Access Bit (DLAB) in U1LCR must be zero in order to access the
U1RBR. The U1RBR is always Read Only.
U1RBR. The U1RBR is always Read Only.
Since PE, FE and BI bits correspond to the byte sitting on the top of the RBR FIFO (i.e.
the one that will be read in the next read from the RBR), the right approach for fetching the
valid pair of received byte and its status bits is first to read the content of the U1LSR
register, and then to read a byte from the U1RBR.
the one that will be read in the next read from the RBR), the right approach for fetching the
valid pair of received byte and its status bits is first to read the content of the U1LSR
register, and then to read a byte from the U1RBR.
4.2 UART1 Transmitter Holding Register (U1THR - 0xE001 0000 when
DLAB = 0, Write Only)
The U1THR is the top byte of the UART1 TX FIFO. The top byte is the newest character in
the TX FIFO and can be written via the bus interface. The LSB represents the first bit to
transmit.
the TX FIFO and can be written via the bus interface. The LSB represents the first bit to
transmit.
The Divisor Latch Access Bit (DLAB) in U1LCR must be zero in order to access the
U1THR. The U1THR is always Write Only.
U1THR. The U1THR is always Write Only.
4.3 UART1 Divisor Latch LSB and MSB Registers (U1DLL - 0xE001 0000
and U1DLM - 0xE001 0004, when DLAB = 1)
The UART1 Divisor Latch is part of the UART1 Baud Rate Generator and holds the value
used to divide the APB clock (PCLK) in order to produce the baud rate clock, which must
be 16x the desired baud rate (
used to divide the APB clock (PCLK) in order to produce the baud rate clock, which must
be 16x the desired baud rate (
). The U1DLL and U1DLM registers together
form a 16 bit divisor where U1DLL contains the lower 8 bits of the divisor and U1DLM
contains the higher 8 bits of the divisor. A 0x0000 value is treated like a 0x0001 value as
division by zero is not allowed.The Divisor Latch Access Bit (DLAB) in U1LCR must be
one in order to access the UART1 Divisor Latches. Details on how to select the right value
for U1DLL and U1DLM can be found later on in this chapter.
contains the higher 8 bits of the divisor. A 0x0000 value is treated like a 0x0001 value as
division by zero is not allowed.The Divisor Latch Access Bit (DLAB) in U1LCR must be
one in order to access the UART1 Divisor Latches. Details on how to select the right value
for U1DLL and U1DLM can be found later on in this chapter.
Table 397: UART1 Receiver Buffer Register (U1RBR - address 0xE001 0000 when DLAB = 0,
Read Only) bit description
Bit
Symbol
Description
Reset Value
7:0
RBR
The UART1 Receiver Buffer Register contains the oldest
received byte in the UART1 RX FIFO.
received byte in the UART1 RX FIFO.
undefined
Table 398: UART1 Transmitter Holding Register (U1THR - address 0xE001 0000 when
DLAB = 0, Write Only) bit description
Bit
Symbol
Description
Reset Value
7:0
THR
Writing to the UART1 Transmit Holding Register causes the data
to be stored in the UART1 transmit FIFO. The byte will be sent
when it reaches the bottom of the FIFO and the transmitter is
available.
to be stored in the UART1 transmit FIFO. The byte will be sent
when it reaches the bottom of the FIFO and the transmitter is
available.
NA