Nxp Semiconductors UM10237 用户手册
UM10237_2
© NXP B.V. 2008. All rights reserved.
User manual
Rev. 02 — 19 December 2008
585 of 792
NXP Semiconductors
UM10237
Chapter 22: LPC24XX I
2
C interfaces I
2
C0/1/2
8.4 I
2
C Data Register (I2C[0/1/2]DAT - 0xE001 C008, 0xE005 C008,
0xE008 0008)
This register contains the data to be transmitted or the data just received. The CPU can
read and write to this register only while it is not in the process of shifting a byte, when the
SI bit is set. Data in I2DAT remains stable as long as the SI bit is set. Data in I2DAT is
always shifted from right to left: the first bit to be transmitted is the MSB (bit 7), and after a
byte has been received, the first bit of received data is located at the MSB of I2DAT.
read and write to this register only while it is not in the process of shifting a byte, when the
SI bit is set. Data in I2DAT remains stable as long as the SI bit is set. Data in I2DAT is
always shifted from right to left: the first bit to be transmitted is the MSB (bit 7), and after a
byte has been received, the first bit of received data is located at the MSB of I2DAT.
8.5 I
2
C Slave Address Register (I2C[0/1/2]ADR - 0xE001 C00C,
0xE005 C00C, 0xE008 000C)
These registers are readable and writable, and is only used when an I
2
C interface is set to
slave mode. In master mode, this register has no effect. The LSB of I2ADR is the general
call bit. When this bit is set, the general call address (0x00) is recognized.
call bit. When this bit is set, the general call address (0x00) is recognized.
8.6 I
2
C SCL High Duty Cycle Register (I2C[0/1/2]SCLH - 0xE001 C010,
0xE005 C010, 0xE008 0010)
8.7 I
2
C SCL Low Duty Cycle Register (I2C[0/1/2]SCLL - 0xE001 C014,
0xE005 C014, 0xE008 0014)
8.8 Selecting the appropriate I
2
C data rate and duty cycle
Software must set values for the registers I2SCLH and I2SCLL to select the appropriate
data rate and duty cycle. I2SCLH defines the number of PCLK cycles for the SCL high
time, I2SCLL defines the number of PCLK cycles for the SCL low time. The frequency is
determined by the following formula (f
data rate and duty cycle. I2SCLH defines the number of PCLK cycles for the SCL high
time, I2SCLL defines the number of PCLK cycles for the SCL low time. The frequency is
determined by the following formula (f
PCLK
being the frequency of PCLK):
Table 516. I
2
C Data Register ( I2C[0/1/2]DAT - addresses 0xE001 C008, 0xE005 C008,
0xE008 0008) bit description
Bit Symbol
Description
Reset Value
7:0 Data
This register holds data values that have been received, or are to
be transmitted.
be transmitted.
0
Table 517. I
2
C Slave Address register (I2C[0/1/2]ADR - addresses 0xE001 C00C,
0xE005 C00C, 0xE008 000C) bit description
Bit Symbol
Description
Reset Value
0
GC
General Call enable bit.
0
7:1 Address
The I
2
C device address for slave mode.
0x00
Table 518. I
2
C SCL High Duty Cycle register (I2C[0/1/2]SCLH - addresses 0xE001 C010,
0xE005 C010, 0xE008 0010) bit description
Bit
Symbol
Description
Reset Value
15:0
SCLH
Count for SCL HIGH time period selection.
0x0004
Table 519. I
2
C SCL Low Duty Cycle register (I2C[0/1/2]SCLL - addresses 0xE001 C014,
0xE005 C014, 0xE008 0014) bit description
Bit
Symbol
Description
Reset Value
15:0
SCLL
Count for SCL LOW time period selection.
0x0004