Alcatel Carrier Internetworking Solutions Switch/Router 用户手册
Viewing Policy Configurations
Page 22-28
Viewing Policy Configurations
Typing
viatrl
brings up the Policy Configuration Table, which shows the policies defined for
the
VLAN
specified.
VLAN VLAN
Rule
Rule
Rule
Rule
Group : Id
Num
Type
Status
Definition
-------------------------------------------------------------------------------------------------------------------------------
3:
5
1
PORT RULE
Disabled
2/7/Brg/1
3:
11
1
NET ADDR RULE
Enabled
IPX Addr = 11223344
IPX Encapsulation = Ethernet
IPX Encapsulation = Ethernet
3:
12
1
NET ADDR RULE Enabled
DECNET Area = 13579
3:
22
1
PORT RULE
Enabled
2/7/Brg/1
3:
23
1
PORT RULE
Enabled
2/7/Brg/1
3:
24
1
MAC RULE
Enabled
082008:003002
082009:803728
082009:803728
3:
25
1
PROTOCOL RULE Enabled
Protocol = IP
3:
26
1
NET ADDR RULE Enabled
IP Addr = 131.1.2.3
IP Mask = 255.255.0.0
IP Mask = 255.255.0.0
3:
27
1
USER RULE
Enabled
Offset = 64
Length = 2
Value = FFFF
Mask = FFFF
Length = 2
Value = FFFF
Mask = FFFF
3:
31
1
PROTOCOL RULE Enabled
Protocol = IP
3:
32
1
NET ADDR RULE Enabled
IPX Addr = 00000001
IPX Encapsulation = Ethernet
IPX Encapsulation = Ethernet
VLAN Group.
The Group to which this AutoTracker
VLAN
is assigned. The Group number is
specified when first creating the
VLAN
.
VLAN ID
. An identification number that you assigned when you created this virtual
LAN
.
Rule Num
. The number of the policy within the
VLAN
definition. Each rule defined for a
VLAN
is numbered sequentially in the order of creation. The rule number is needed when you want
to modify or delete a rule definition.
to modify or delete a rule definition.
Rule Type
. The type of
VLAN
policy. The Rule Type can be a port policy (
PORT RULE
),
MAC
Address policy (
MAC RULE
), network address policy (
NET ADDR RULE
), Protocol policy
(
PROTOCOL RULE
), or a user-defined policy (
USER RULE
). You set up
VLAN
policies when you
create or modify the
VLAN
.
Rule Status
. Indicates whether the rule for this row is Enabled or Disabled. If the rule is
enabled, then the
VLAN
is using the rule definition to determine
VLAN
membership. If
Disabled, then the
VLAN
is not using this rule to determine membership. Note that this Rule
Status is different from the Admin Status for the
VLAN
since it controls only this specific rule
within this specific
VLAN
. You can enable or disable the rule using the
modatvl
command.
Rule Definition
. Details of this rule. For a Port Rule, this column lists the virtual interface for the
Port included in the
VLAN
as
<slot>/<port>/<service>/<instance>
For example, the port defined for the first row in the table applies to the first bridge instance
on port 7 on the module in slot 2 of the switch. For a
on port 7 on the module in slot 2 of the switch. For a
MAC
address rule, this column lists the
MAC
address for the device in the
VLAN
. For a Network Address Rule, the column will list the
address (
IP
or
IPX
) and the IP Mask (
IP
) or the Encapsulation type (
IPX
). For a Protocol policy,
the column list the protocol used to determine membership. And in a User-Defined rule, the
offset, length, value, and mask are listed.
offset, length, value, and mask are listed.