Xerox 12.7 B 114 用户手册
6.5.1 Clear Last Image
When the “Clear Last Image” feature is selected on the Xerox Wide Format Scan System, it may
take a few minutes for a Photo or Color mode scanned document to clear out. After scanning a
document, this feature is accessed by selecting the “C” key on the scanner. It will bring up the
“CLEAR SCANNED IMAGE” screen. Use the “Next” button to select “CLEAR LAST IMAGE”, and
then press “ENTER”.
take a few minutes for a Photo or Color mode scanned document to clear out. After scanning a
document, this feature is accessed by selecting the “C” key on the scanner. It will bring up the
“CLEAR SCANNED IMAGE” screen. Use the “Next” button to select “CLEAR LAST IMAGE”, and
then press “ENTER”.
6.5.2 Invert Feature and Recall Last Job
Scan a document. Press the Transform key. Select “Recall Last Job”. If the Invert feature
(changes dark to light and vice versa) is selected before printing the recalled document, the
document will not be inverted. It will need to be rescanned to get the inverted image.
(changes dark to light and vice versa) is selected before printing the recalled document, the
document will not be inverted. It will need to be rescanned to get the inverted image.
6.5.3 Scan-to-Print and Margins
When performing a scan-to-print operation the scanned image is printed using the current printer
processing defaults including margins. If the image scanned is exactly the width of the paper,
then the processing default margins should be set to zero to prevent the image from being clipped
or placed on a larger sheet of paper.
processing defaults including margins. If the image scanned is exactly the width of the paper,
then the processing default margins should be set to zero to prevent the image from being clipped
or placed on a larger sheet of paper.
6.5.4 Width Detection Sensors and Finishing
When using the width detection sensors, if the document is a little bit off-center, this could cause
problems for folding, as the document printed may be square. This is most problematic with A, B,
and C sizes. Documents must be centered when using the sensors for width detection.
problems for folding, as the document printed may be square. This is most problematic with A, B,
and C sizes. Documents must be centered when using the sensors for width detection.
6.5.5 Background Suppression
The scanner uses the first few inches of a document to determine the background suppression. If
the first few inches of the document being scanned are not representative of the entire document,
either too much or too little of the background will be removed. If this occurs, try physically turning
the document 90 degrees and scan it again. Continue with this until an edge is found that
produces a good scan.
the first few inches of the document being scanned are not representative of the entire document,
either too much or too little of the background will be removed. If this occurs, try physically turning
the document 90 degrees and scan it again. Continue with this until an edge is found that
produces a good scan.
6.5.6 Scaling shaded documents
Scaling documents with error diffused shaded areas should be done in a photo mode to produce
the best image quality. Line and normal modes tend to exaggerate the shading dots making them
more visible.
the best image quality. Line and normal modes tend to exaggerate the shading dots making them
more visible.
6.5.7 50000015 errors while copying
Occasional 50000015 errors have been seen while scanning more than 128 documents on the
6030/6050 system. This happens when an experienced operator gets a significant number of
pages ahead of the printer causing a queue that is larger than the system can hold. The solution
is to wait for several of the pages to complete printing before copying any additional documents.
6030/6050 system. This happens when an experienced operator gets a significant number of
pages ahead of the printer causing a queue that is larger than the system can hold. The solution
is to wait for several of the pages to complete printing before copying any additional documents.
6.5.8 Recalling sets
When a set is recalled, the scanner UI settings are not set to reflect their state for the last page
scaled, but are in a “neutral” state to prevent unintentional overriding of setting for the set. If a
setting (like scale, page size, etc) is changed it will affect the entire document set.
scaled, but are in a “neutral” state to prevent unintentional overriding of setting for the set. If a
setting (like scale, page size, etc) is changed it will affect the entire document set.
Page 12