Porter-Cable PCB270TS 用户手册
– 30 –
TROUBLESHOOTING GUIDE
To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before
making any adjustments.
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our service website at www.portercable.
com. You can also order parts from your nearest Porter-Cable Factory Service Center or Porter-Cable Authorized
Warranty Service Center. Or, you can call our Customer Care Center at (888) 609-9779.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information about Porter-Cable, its
factory service centers or authorized warranty service centers, visit our website at www.portercable.com or call our
Customer Care Center at (888) 609-9779. All repairs made by our service centers are fully guaranteed against
defective material and workmanship. We cannot guarantee repairs made or attempted by others.
You can also write to us for information at
making any adjustments.
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our service website at www.portercable.
com. You can also order parts from your nearest Porter-Cable Factory Service Center or Porter-Cable Authorized
Warranty Service Center. Or, you can call our Customer Care Center at (888) 609-9779.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information about Porter-Cable, its
factory service centers or authorized warranty service centers, visit our website at www.portercable.com or call our
Customer Care Center at (888) 609-9779. All repairs made by our service centers are fully guaranteed against
defective material and workmanship. We cannot guarantee repairs made or attempted by others.
You can also write to us for information at
Power Tool Specialists, Inc. 684 Huey Road, Rock Hill, SC 29730
,
(888) 609-9779 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your
tool (model number, type, serial number, etc.).
tool (model number, type, serial number, etc.).
PROBLEM
POSSIBLE CAUSES
CORRECTIVE ACTION
Saw will not start.
1. Saw is not plugged in.
2. Fuse blown or circuit breaker tripped.
3. Cord is damaged.
3. Cord is damaged.
1. Plug in saw.
2. Replace fuse or reset circuit breaker.
3. Have cord replaced by Porter-Cable Service
Center or Authorized Service Station.
Does not make
accurate 45° and
accurate 45° and
90° rip cuts.
1. Positive stop not adjusted correctly.
2. Tilt angle pointer not set accurately.
1. Check blade with square and adjust positive
stop.
2. Check blade with square and adjust to zero.
Material pinched blade
when ripping.
when ripping.
1. Rip fence not aligned with blade.
2. Warped wood, edge against fence is not
straight.
1. Check and adjust rip fence.
2. Select another piece of wood.
Material binds on riving
knife.
1. Riving knife not aligned correctly with blade. 1. Check and align riving knife with blade.
Saw makes
unsatisfactory cuts.
unsatisfactory cuts.
1. Dull blade.
2. Blade mounted backwards.
3. Gum or pitch on blade.
3. Gum or pitch on blade.
4. Incorrect blade for work being done.
5. Gum or pitch on blade causing erratic feed.
5. Gum or pitch on blade causing erratic feed.
1. Replace blade.
2. Turn the blade around.
3. Remove blade and clean with turpentine
3. Remove blade and clean with turpentine
and coarse steel wool.
4. Change the blade.
5. Clean table with turpentine and steel wool.
5. Clean table with turpentine and steel wool.
Material kicked back
from blade.
from blade.
1. Rip fence out of adjustment.
2. Riving knife not aligned with blade.
3. Feeding stock without rip fence.
4. Riving knife not in place.
5. Dull blade.
6. The operator letting go of material before it
is past saw blade.
7. Miter angle lock knob is not tight.
1. Align rip fence with miter gauge slot.
2. Align riving knife with blade.
3. Install and use rip fence.
4. Install and use riving knife. (with guard)
5. Replace blade.
6. Push material all the way past saw blade
before releasing work.
7. Tighten knob.
WARNING
!