Milwaukee 2426-22 用户手册

Cat. No. Volts DC No load OPM Hex Wrench

12

5000 - 20,000

5 mm

Direct Current

Underwriters Laboratories, Inc.
United States and Canada

nated battery packs. Use of any other battery 
packs may create a risk of injury and fi re.

from other metal objects like paper clips, 
coins, keys, nails, screws, or other small metal 
objects that can make a connection from one 
terminal to another. Shorting the battery termi-
nals together may cause burns or a fi re.

ed from the battery; avoid contact. If contact 
accidentally occurs, fl ush with water. If liquid 
contacts eyes, additionally seek medical help. 
Liquid ejected from the battery may cause irritation 
or burns.

repair person using only identical replacement 
parts. This will ensure that the safety of the power 
tool is maintained.

when performing an operation where the cutting 
accessory may contact hidden wiring or its own 
cord. Cutting accessory contacting a "live" wire may 
make exposed metal parts of the power tool "live" 
and could give the operator an electric shock. 

and support the workpiece to a stable platform. 
Holding the work by hand or against your body 
leaves it unstable and may lead to loss of control.

moving parts. Do not reach underneath the 
workpiece. 

• Do not use dull or damaged blade, which can 

cause excessive friction, blade binding and kick-
back.

heads before scraping. Hitting hard objects with 
blade may cause the tool to kick back.

• Maintain labels and nameplates. These carry 

important information. If unreadable or missing, 
contact a MILWAUKEE service facility for a free 
replacement.

• WARNING: Some dust created by power sanding, 

sawing, grinding, drilling, and other construction 
activities contains chemicals known to cause 
cancer, birth defects or other reproductive harm. 
Some examples of these chemicals are:

•lead from lead-based paint
•crystalline silica from bricks and cement and other 

masonry products, and

• arsenic and chromium from chemically-treated 

lumber. 

  Your risk from these exposures varies, depending 

on how often you do this type of work. To reduce 
your exposure to these chemicals: work in a well 
ventilated area, and work with approved safety 
equipment, such as those dust masks that are spe-
cially designed to fi lter out microscopic particles.

1. Accessory bolt
2. Outer fl ange
3. Adapter
4. Inner fl ange
5. Speed dial
6. Fuel gauge
7. On/Off switch

Changing Accessories
1. Remove the battery pack.
2. Place the tool upside down on a fl at surface. 
3. Use the hex wrench to remove the accessory 

bolt. 

4. Remove the outer fl ange and any accessories 

and adapter.

5. Clean  bolt,  fl anges, adapter and accessories of 

all dirt and debris. 

6. Place the adapter (if necessary), accessory, 

outer fl ange and bolt onto the tool. Determine the 
need for an adapter by using the chart. Tighten 
securely using a hex wrench.

2

1

5

3

6

7

adapter not needed

adapter not needed

4

Inserting/Removing the Battery
To remove the battery, push in the release buttons 
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body of 
the tool. Make sure it latches securely into place.

Fuel Gauge
To determine the amount of charge left in the bat-
tery, turn the tool ON. The Fuel Gauge will light up 
for 2-3 seconds. When less than 10% of charge is 
left, 1 light on the fuel gauge will fl ash slowly.
To signal the end of charge, 1 light on the fuel gauge 
will fl ash quickly for 2-3 seconds and the tool will 
not run. Charge the battery pack.
If the tool or battery becomes too hot, the fuel 
gauge lights will fl ash in an alternating pattern and 
the tool will not run. Allow the tool and battery to 
cool down.
To protect against high torque, binding, stalling, 
and short circuit situations, the tool will shut down 
and all the fuel gauge lights will fl ash. Release the 
trigger and restart.

Typical Applications
A large variety of accessories are available for 
applications such as sawing/cutting, scraping, 
and sanding.

Sawing/Cutting
Install a sawing/cutting blade at an angle easy to 
use. Properly clamp the workpiece. Set the speed 
dial to a high speed. Start the tool and allow it to 
reach full speed. Use moderate pressure to avoid 
burning or scorching the workpiece.

Scraping
Install a scraping blade at an angle easy to use. 
Start the tool and allow it to reach full speed. Use 
light pressure and a low angle to avoid gouging 
and damaging the workpiece.

Sanding
Install a sanding backing pad at an angle easy to 
use. Attach a sanding disc, or cut sandpaper to fi t 
the backing pad. Generally, use 24 or 36 grit for 
heavy stock removal; 50, 60, or 80 grit for medium 
stock removal and 120 grit for fi nishing.  Always 
begin with a coarse grit, using successively fi ner 
grits to obtain the desired fi nish.  
Properly clamp the workpiece. Start the tool and 
allow it to reach full speed. Use light pressure and 
long, sweeping, side to side strokes, advancing 
forward to produce the desired fi nish.