Euro-Pro V1504C 用户手册

Upholstery Brush
The upholstery brush is conveniently 
mounted on the back of the main body 
of the vacuum cleaner.  The brush can 
be used for cleaning the furniture, 
Venetian blinds, books, lamp shades 
and shelves.  (Fig. 14)

This attachment is stored on the right 
side of the cleaner on it’s own holder in 
front of where the flexible hose ttaches
to the hose connector.  This tool is 
designed to extend your reach.  Attach 
this accessory by it’s narrower end to 
the flexible hose and use for hard to 
reach places. (Fig. 15)

The turbo brush conveniently attaches 
to the handle with an attaching bracket. 
1. Ensure that the handle is attached 

to the main body before attaching 
the turbo brush to the handle.

2. First attach the turbo brush to the 

attaching bracket by hooking the 
edge of the opening under the 
trapdoor on the bottom of the turbo 
brush to the flat part of the bracket. 
Then press the tube part of the 
turbo brush against the clip on the 
bracket until the two pieces snap 
together.

3. Hold the assembled pieces by the 

turbo brush and touch the two clips 
on the bracket to 
the metal tube of 
the handle.  Hold 
the handle from 
the top and 
squeeze the two  
pieces together, 
putting more 
force on the 
bigger clip until 
the bracket 
snaps on. 

4. Remove the turbo 

brush from the 
bracket in order to
use. (Fig. 16)

1. Pull the pre-motor filter frame out of 

the main body. (Fig. 11)

2. Remove the pre-motor filter from the 

frame and wash both the filter and 
the frame under the tap with 
lukewarm water. (Fig. 12)

3. Allow both parts to air dry 

completely before placing the filter 
back in the frame and sliding the 
frame back into the main body.  Let 
the pre-motor filter and pre-motor 
filter frame air dry for 24 hours.  DO 
NOT DRY IN THE DRYER.

Make sure the vacuum 

cleaner is turned off when attaching or 
removing any accessories.

: DO  NOT pull the vacuum 

cleaner around by the hose.  DO NOT
over stretch the hose.  Trying to reach 
beyond the hose’s extent may cause 
the vacuum cleaner to tip over.

The crevice tool is located inside the 
extension tube and can be used for 
radiators, crevices, corners, 
baseboards and between cushions. 
(Fig. 13)

The efficiency of your turbo brush 
depends on the bristle brush rotating at 
high speed.  Strong air suction is needed 
to accomplish this.  In order to ensure 
that maximum air suction is maintained, 
please read the following instructions:
1. Empty the dust cup frequently 

during use.

2. Inspect the rotating bristle brush 

and air turbine wheel regularly.  
Inspect the turbine wheel and air 
passage for debris and/or blockages. 
Remove debris if present. 

3. Inspect the rotating brush for a build 

up hair or string.  If present, remove 
by carefully cutting with scissors. 
Avoid damaging or cutting the 
bristles. 

To clean the pet hair turbo brush:
1. Hold the turbo brush in your hand 

and with the help of a screwdriver, 
gently pry the cover off. (Fig. 17)

1. Place the vacuum cleaner in the 

upright position.

2. Set the carpet height adjustment 

knob to the highest setting “     ”.

3. To attach the accessories to the 

flexible hose, remove the hose from 
the hose connector and push the 
desired accessory onto the end. 

4. If additional length is required, the 

handle may be used.  Remove the 
handle from the main body by first 
lifting the handle locking lever.  Push 
the end of the flexible hose into the 
opening at the back of the handle. 

Attach the desired accessory to the 

end of the handle. 

5. The crevice tool, turbo brush and 

upholstery brush can also be 
attached to the end of the extension 
tube. 

6. Ensure that the attachment you are 

using is appropriate for the surface 
you are cleaning. 

7. To return to vacuuming the floor, 

perform the following steps:
• Detach the hose from the handle 

and push it snugly back into the 
hose connector.

• Hang the flexible hose back onto 

the hose holder. 

• Return the handle to it’s regular 

position in the opening on top of 
the main body and push down the
handle locking lever to lock the
handle into place. 

• Return the carpet height 

adjustment knob to the appropriate 
setting.

2. Inspect turbine wheel and air 

passage for debris and/or blockage. 
Remove any debris if present.

3. Inspect the rotating brush for built-up 

hair or string.  If present, remove by 
carefully cutting with scissors.  Avoid 
damaging or cutting bristles.

4. Once clean, align the cover of the 

turbo brush with the edge of the 
brush and snap it closed. (Fig. 18)