Pioneer VSX-AX5i-G 用户手册
Setting Up for Surround Sound
43
En
SURROUND SETUP
Channel Level
The following steps show you how to balance the sound output level of your speakers. Proper speaker balance is
essential for obtaining high quality surround sound. If continuing from SPEAKER SETTING go to step 1. If starting
fresh, complete steps 1–2 on page 40.
essential for obtaining high quality surround sound. If continuing from SPEAKER SETTING go to step 1. If starting
fresh, complete steps 1–2 on page 40.
1 CHANNEL LEVEL should be selected. If it
isn’t use the
buttons to select and
press ENTER.
2 There are two ways to set the
CHANNEL LEVEL: MANUAL or AUTO.
Select a setting mode with the
Select a setting mode with the
buttons and press ENTER.
Test tones will be output.
WARNING: Be prepared! The test tones are output at a
high volume level.
MASTER VOLUME rotates to the reference position (0 dB)
and the display on the receiver flashes TEST TONE. After a
few seconds the test tone is output.
MANUAL: move the test tone manually and adjust the chan-
nel level.
AUTO: the test tone moves by itself and you adjust the levels.
WARNING: Be prepared! The test tones are output at a
high volume level.
MASTER VOLUME rotates to the reference position (0 dB)
and the display on the receiver flashes TEST TONE. After a
few seconds the test tone is output.
MANUAL: move the test tone manually and adjust the chan-
nel level.
AUTO: the test tone moves by itself and you adjust the levels.
3 Adjust the speaker level with the
instructions below for the method you
chose.
chose.
Adjust the channel level from –10 dB to +10 dB in 0.5 dB
increments.
The default setting is 0 dB.
increments.
The default setting is 0 dB.
In MANUAL (manual test tone) mode
To switch the test tone between each speaker use the
To switch the test tone between each speaker use the
buttons and push ENTER. Adjust the level of each speaker
using the
using the
buttons and ENTER. When done go to step 4.
In AUTO (automatic test tone) mode
This mode switches the test tone between each speaker
automatically. The test tone output cycles through the speak-
ers in the following order:
This mode switches the test tone between each speaker
automatically. The test tone output cycles through the speak-
ers in the following order:
Adjust the level of each speaker using the
buttons as the
test tone is emitted and wait for it to move to the next
speaker. When done go to step 5.
If you want to change a setting before proceeding you
need to complete the procedure and start over from step 1.
speaker. When done go to step 5.
If you want to change a setting before proceeding you
need to complete the procedure and start over from step 1.
4 When you have the levels you want
press ENTER. EXIT should be selected (if
it isn’t select it with the
it isn’t select it with the
buttons).
5 Press ENTER.
Next, proceed to SPEAKER DISTANCE next page.
1
2
3
1-5
in AUTO setting
in MANUAL setting
Memo:
• If your subwoofer has a volume control, set it
• If your subwoofer has a volume control, set it
to the middle position before doing these
operations.
operations.
• If you are using a Sound Pressure Level
(SPL) meter take the readings from your
main listening position and adjust the level
of each speaker to 75dB SPL (C-weighting/
slow reading).
main listening position and adjust the level
of each speaker to 75dB SPL (C-weighting/
slow reading).
• The volume of the subwoofer test tone tends
to sound lower than it actually is. You may
need to adjust the level after testing your
system with an actual soundtrack.
need to adjust the level after testing your
system with an actual soundtrack.
• You can also set the channel level manually
at any time by pressing RECEIVER then
EFFECT/CH SEL on the remote control. Use
the (+/–) buttons directly below the EFFECT/
CH SEL button to adjust the level.
EFFECT/CH SEL on the remote control. Use
the (+/–) buttons directly below the EFFECT/
CH SEL button to adjust the level.
VSX-AX5i.book Page 43 Friday, May 23, 2003 6:33 PM