Hoover SteamVac LS 用户手册
To clean the outside of the machine,
wipe off dirt with a cloth dampened in
warm water and mild detergent.
wipe off dirt with a cloth dampened in
warm water and mild detergent.
Fill clean solution tank (upper tank)
with HOOVER Carpet/Upholstery
Detergent according to instructions for
Figs.
Figs.
to 2-16
3. Dry hands and plug cord into a
4. To avoid walking on damp carpet,
start at the end of the room farthest from
the door or path to sink where tanks will
start at the end of the room farthest from
the door or path to sink where tanks will
be emptied and filled
Step on handle release pedal and lower
handle to operating position; turn deep
cleaner ON.
handle to operating position; turn deep
cleaner ON.
5. Squeeze trigger to release cleaning
solution and slowly push deep cleaner
forward (equals one wet stroke).
solution and slowly push deep cleaner
forward (equals one wet stroke).
6. Continue to squeeze trigger and
slowly pull deep cleaner back toward
you (second wet stroke). Release trigger
and slowly push deep cleaner forward
over area just sprayed with solution (dry
stroke). Then slowly pull deep cleaner
back toward you without squeezing trig-
ger (dry stroke).
slowly pull deep cleaner back toward
you (second wet stroke). Release trigger
and slowly push deep cleaner forward
over area just sprayed with solution (dry
stroke). Then slowly pull deep cleaner
back toward you without squeezing trig-
ger (dry stroke).
7. Overlap strokes by 1 inch to help pre-
vent streaking.
Keep nozzle flat on floor for both for-
ward and reverse strokes.
vent streaking.
Keep nozzle flat on floor for both for-
ward and reverse strokes.
8. For heavily soiled areas, repeat, To
It is best to alternate wet and dry
strokes as described above.
strokes as described above.
For best cleaning results and to aid in
faster drying of carpet, end with more
dry strokes. (Continue using dry strokes
until little water is visible passing
through the recovery tank lid.)
Empty recovery tank when the motor
sound becomes higher pitched and
there is a loss in suction (see
faster drying of carpet, end with more
dry strokes. (Continue using dry strokes
until little water is visible passing
through the recovery tank lid.)
Empty recovery tank when the motor
sound becomes higher pitched and
there is a loss in suction (see
“Automatic shut-off”, Fig 2-6)
When finished cleaning, follow “After
cleaning” instructions on pages
cleaning” instructions on pages
Your HOOVER SteamVac deep cleaner
may also be used to pick up
may also be used to pick up
on carpet,
upholstery, or bare floors.
For best results, pick up spills immedi-
ately by placing the stair/upholstery noz-
zle just above the spill and suction up
any residue on top of the carpet. If the
spill remains, place either the stair/
upholstery nozzle or floor nozzle
brushes turned
ately by placing the stair/upholstery noz-
zle just above the spill and suction up
any residue on top of the carpet. If the
spill remains, place either the stair/
upholstery nozzle or floor nozzle
brushes turned
OFF in
front of the spill,
pull the nozzle very slowly over the spill
initially with suction only Repeat with spray
and suction.
initially with suction only Repeat with spray
and suction.
(this will help
prevent spreading the spill).
If a spot is left, the stair/upholstery nozzle is
generally more effective for removing it.
Although no cleaning solution can com-
pletely remove all spots, they can be treat-
ed by following the instructions provided by
the manufacturer of the carpet, upholstery,
or bare floor surface being cleaned.
generally more effective for removing it.
Although no cleaning solution can com-
pletely remove all spots, they can be treat-
ed by following the instructions provided by
the manufacturer of the carpet, upholstery,
or bare floor surface being cleaned.
When finished, follow “After cleaning”
instructions on pages
How to attach bare
floor attachment
To prevent possible leaking, remove
clean solution tank (Fig. 2-10) and
recovery tank ( Fig 2-17) before posi-
tioning bare floor attachment.
Set tanks aside (do not set tank on furni-
ture).
clean solution tank (Fig. 2-10) and
recovery tank ( Fig 2-17) before posi-
tioning bare floor attachment.
Set tanks aside (do not set tank on furni-
ture).
1. With handle in upright position, tilt
cleaner back so that handle rests on the
floor.
floor.
2. With foam strip (A) (located under the
netting) in position as shown, place
netting) in position as shown, place
attachment on front of nozzle (B).
Make sure arrow on end of attachment
points in the direction as shown.
Make sure arrow on end of attachment
points in the direction as shown.
3. Push attachment against nozzle while
rotating attachment downward until both
ends snap into place.
rotating attachment downward until both
ends snap into place.