Hoover SteamVac LS 用户手册
4. Return deep cleaner to upright posi-
tion Lower handle and replace recovery
tank.
tion Lower handle and replace recovery
tank.
5. Raise handle to upright position and
reposition clean solution tank.
reposition clean solution tank.
Fill clean solution tank with HOOVER
Bare Floor Cleaner according to instruc-
tions for Figs. 2-10 to
tions for Figs. 2-10 to
2.
3. Dry hands and
4. Step on handle release pedal and
lower handle to operating position; turn
deep cleaner ON.
lower handle to operating position; turn
deep cleaner ON.
5. To release solution, press trigger.
Slowly move deep cleaner forward and
backward over area to be cleaned.
Slowly move deep cleaner forward and
backward over area to be cleaned.
pick up dirty solution, release trig-
ger and slowly move deep cleaner over
area where solution has just been
area where solution has just been
persed. Use both forward and reverse
strokes.
strokes.
7. Empty recovery tank when the motor
sound becomes higher pitched and
there is a loss in suction (see “Automatic
shut-off”, Fig 2-6)
sound becomes higher pitched and
there is a loss in suction (see “Automatic
shut-off”, Fig 2-6)
8. When finished cleaning, follow “After
cleaning” instructions on pages
cleaning” instructions on pages
and remove attachment from
nozzle. Rinse it in clear water.
B
A
C
D
How to attach tools
Place handle in upright position and
remove hose from rack.
All tools attach to the hose in the same
manner:
2. Connect tool to hose by sliding it onto
connector until the tab (D) locks it
securely.
All tools attach to the hose in the same
manner:
2. Connect tool to hose by sliding it onto
connector until the tab (D) locks it
securely.
Using your thumb,
on the
to remove tool as
shown.
Before using tool
It may be necessary to remove air from
the system (“prime the pump”) so the
clean solution will flow to the tool. Follow
these steps:
clean solution will flow to the tool. Follow
these steps:
Attach tool to hose and turn the deep
cleaner ON.
the tool on a hard surface or
has rotating
brushes for extra scrubbing action on
small carpet areas, carpeted stairs and
upholstery. Brushes can be removed for
converting to the scrub module.
small carpet areas, carpeted stairs and
upholstery. Brushes can be removed for
converting to the scrub module.
has a
in brush to help provide the
action some spots may need for
removal.
action some spots may need for
removal.
attaches to the base of the
powered hand tool (in place of brush
module). Can be used to scrub stub-
born areas such as scuff marks, dried
spills, and in hard to reach areas on
hard surfaces.
module). Can be used to scrub stub-
born areas such as scuff marks, dried
spills, and in hard to reach areas on
hard surfaces.
can be used to clean
along edges of carpet, carpeted stairs
and on upholstery.
and on upholstery.
against your hand to block off the suc-
tion.
3. Wait a few seconds (can take up to
tion.
3. Wait a few seconds (can take up to
15 seconds). Then squeeze the trigger
and begin cleaning.
Follow the instructions on pages 12-13
for the appropriate cleaning task.
Follow the instructions on pages 12-13
for the appropriate cleaning task.
Attaching scrub module
1. Open the tool door and remove the
powered hand tool.
2. Grasp the sides of the brush module
and lift it from the base (F).
and lift it from the base (F).
3. Pull scrub module from deep cleaner
and snap it onto the base.
and snap it onto the base.
It may be necessary to rotate the
scrub module (G) slightly so it will align
properly to the base.
properly to the base.
Using the scrub tool
1. Fill clean solution tank with HOOVER
Bare Floor Cleaner according to instruc-
tions for Figs. 2-10 to 2-16.
2. Hold scrub tool above area to be
cleaned and press trigger to dispense
solution.
cleaned and press trigger to dispense
solution.
3. Release trigger and scrub area with
tool. Pick up dirty solution with
squeegee as shown.
Apply Bare Floor Cleaner with the
spray bottle.
2. Scrub area with tool. Pick up dirty
solution with squeegee as shown.
solution with squeegee as shown.