Hoover SteamVac LS 用户手册
Be sure to check the cleaning code on
your upholstery.
your upholstery.
Place handle in upright position.
2. Fill clean solution tank with HOOVER
Carpet/Upholstery Detergent according
to instructions for Figs. 2-10 to 2-16.
Carpet/Upholstery Detergent according
to instructions for Figs. 2-10 to 2-16.
3. Attach tool to end of hose.
4. Dry hands and plug deep cleaner into
a
a
5. Turn deep cleaner ON. If necessary,
refer to “Before using tool” section to
remove air from the system.
refer to “Before using tool” section to
remove air from the system.
6. Gently press the tool (A) or (B) onto
the fabric. Press the trigger and slowly
pull the nozzle over the fabric.
the fabric. Press the trigger and slowly
pull the nozzle over the fabric.
7. Overlap strokes by
inch to help
prevent streaking.
Make additional strokes without pressing
the trigger to remove more moisture.
the trigger to remove more moisture.
8. To clean in corners or creases, lift the
tool one-half inch from the fabric and
press the solution trigger.
tool one-half inch from the fabric and
press the solution trigger.
9. Vacuum up the solution with the tool
without pressing the trigger.
without pressing the trigger.
10. For heavily soiled areas, it may be
necessary to repeat the cleaning
process. Make crisscrossing strokes to
the original pattern; overlap each pass.
process. Make crisscrossing strokes to
the original pattern; overlap each pass.
If additional cleaning is necessary, wait
until the upholstery is completely dry
before using the tool again.
until the upholstery is completely dry
before using the tool again.
11. Empty recovery tank when the motor
sound becomes higher pitched and
there is a loss in suction (see “Automatic
shut-off”, Fig. 2-6).
there is a loss in suction (see “Automatic
shut-off”, Fig. 2-6).
When finished cleaning, follow “After
cleaning” instructions on page 9 and
cleaning” instructions on page 9 and
“After using tool” instructions on page 12.
Storage
Before storing:
l
Empty solution tank and rinse
thoroughly with clean water.
l
Replace
solution tank and
turn deep cleaner ON. Squeeze
trigger and push deep cleaner for-
ward and back several times to
trigger and push deep cleaner for-
ward and back several times to
expel any solution remaining in the
deep cleaner’s system. (Do not
use deep cleaner on wood floors.)
deep cleaner’s system. (Do not
use deep cleaner on wood floors.)
l
Empty recovery tank and rinse
thoroughly with clean water.
Lubrication
The motor Is equipped with bearings
which contain sufficient lubrication for
the life of the motor. The addition of
which contain sufficient lubrication for
the life of the motor. The addition of
lubricant could cause damage.
Service
To obtain approved HOOVER service
and genuine HOOVER parts, locate the
nearest
by:
l
checking the Yellow Pages under
Vacuum Cleaners Household” OR
l
checking the list of Factory Service
Centers provided with this cleaner
OR
OR
l
calling
for an
automated referral of authorized
service outlet locations (U.S. only)
OR-
service outlet locations (U.S. only)
OR-
* checking the Service section of The
Hoover Company on-line at
Hoover Company on-line at
send your cleaner to The Hoover
Company in North Canton for service,
this will only result in delay.
this will only result in delay.
If further assistance Is needed, contact
The Hoover Company Consumer
Response Center, North Canton, Ohio
44720 Phone: 330-499-9499.
44720 Phone: 330-499-9499.
In Canada, contact Hoover Canada,
Burlington, Ontario
Burlington, Ontario
Phone: l-800-263-6376.
Always identify your cleaner by the
plete
model number when requesting
information or ordering parts. (The model
number appears on the back of the han-
dle.)
number appears on the back of the han-
dle.)